manualshive.com logo in svg

PEUGEOT TSDI, Руководство по ремонту

Поделиться
Скачать
PEUGEOT TSDI Скачать руководство пользователя страница 28

MISCELLANEOUS OPERATIONS

Page: 28

Reproduction or translation, even partial, are forbidden without the written consent of Peugeot Motocycles

To remove/refit the drive pulley rollers

 

- Remove the transmission cover 8 fixing bolts

 - Remove the cover and its locating pin
 - Lock the fixed flange (2) with tool
 P/N 755874
 - Remove the fixed flange nut (1)
 - Remove the fixed flange

 - Remove the guide hub (1)
 - Remove the cover three fixing bolts (2)
 - Remove the cover (3)
 - Remove the coil (4)
 - Remove the holder (5) and its 3 plastic guides (6)
 - Remove the 6 rollers (7)
 - Remove the O-ring (8) from the rotating flange
(9)

After cleaning, check the condition of the rollers,
they must be changed if they show flats due to
excessive wear

To re-assemble, proceed in reverse order to
disassembly after lightly greasing the rollers and
rotating flange inside (high temperature grease)

Note: 

Do not over-grease to avoid splashing the

belt

Содержание TSDI












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды