PEUGEOT TSDI Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 43

background image

SPECIAL WORK AND PROCEDURES

Page: 37

Reproduction or translation, even partial, are forbidden without the written consent of Peugeot Motocycles

To remove the fuel pump

- Remove the ignition key after unlocking the

saddle
- Remove the saddle/locker assembly
- Remove the grab handle
- Remove the mud-flap
- Remove the rear panel assembly
- Clamp the fuel inlet hose (1) with hose clamp P/N
755996
- Disconnect the fuel inlet pipe (1) from the fuel
pump (2)

- Carry out the procedure used to lower the pressure
in the fuel system (see instruction 1)
- Disconnect the fuel inlet pipe (3) from the fuel
pump (2)
- Remove the fuel pump 2 fixing volts (4)
- Remove the fuel pump
- Disconnect the fuel pump

Re-assembly:

Proceed in reverse order to

disassembly and bleed the fuel system (see
instruction 2)

(if changed, these clips must not be replaced by
screw-type clips)

Check:

Using the diagnostic tool, check for fault

codes, clear them if necessary

«
...
35
36
37
38
39
...
»

Содержание TSDI












































Отзывы:

Нет отзывов

Похожие инструкции для TSDI

Бренд: O.S. engine Страницы: 21

Бренд: O.S. engine Страницы: 25

Бренд: YOODA Страницы: 6

Бренд: Iveco Motors Страницы: 6

Бренд: Man Страницы: 64

Бренд: Kohler Страницы: 85

Бренд: Briggs & Stratton Страницы: 12

Бренд: Man Страницы: 18

Бренд: TOHATSU Страницы: 292

Бренд: Westerbeke Страницы: 2

10.0 KW-60Hz SBEG

Бренд: Westerbeke Страницы: 104

Бренд: Robin America Страницы: 32

Бренд: Robin America Страницы: 35

Бренд: Magnum Страницы: 7

MOTOR ELITE-i BOX 45 Series

Бренд: gaviota Страницы: 24

Бренд: Stober Страницы: 48

Бренд: Honda Страницы: 86

Бренд: DANA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды