manualshive.com logo in svg

PEUGEOT TSDI, Руководство по ремонту

Поделиться
Скачать
PEUGEOT TSDI Скачать руководство пользователя страница 29

MISCELLANEOUS OPERATIONS

Page: 29

Reproduction or translation, even partial, are forbidden without the written consent of Peugeot Motocycles

To remove the clutch lining assembly

 

- Remove the transmission cover 8 fixing bolts

 - Remove the cover and its locating pin
 - Lock the clutch drum (1) with the pin wrench
P/N 752237
 - Remove the nut
 - Clamp the two strands of the belt to lower it
between the flanges
 - Remove the clutch drum and the clutch-drive
pulley assembly
 - Lock the assembly with tool P/N 752127
clamped in the jaws of a vice
 - Remove nut (1) using spanner P/N 752361
 - Decompress tool P/N 752127

 - Remove the clutch lining assembly (2)
 - remove the upper centring sleeve (3) from the
spring
 - Remove the spring (4)
 - Remove the lower centring sleeve (5) from the
spring
 - Remove the 3 pins (6) from the governor seat
 - Separate the fixed (7) and rotating (8) flanges

To refit the clutch lining assembly

After checking the 2 lip seals (9) and the 2 O-rings
of the rotating flange (8) are in good condition,
grease the governor seat 3 pins (6) (high
temperature grease) and assemble the parts in
reverse order to removal

 - Compress the assembly with tool P/N 752127
 - Tighten the nut (1) to the recommended torque

Note:

 Before fitting the drive pulley to the input

shaft, fit the belt into the pulley bottom by opening
the flanges by hand

 - Fit the clutch cover
 - Fit and tighten the nut to the recommended
torque
 - Fit the cover with its locating pin
 - Fit the cover 8 fixing bolts

Содержание TSDI












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды