EN
ES
FR
IT
NL
DE
www.petsafe.net 11
10 www.petsafe.net
to replace Clock Battery:
Remove Interior Frame from wall to access the Clock Battery Cover. Remove Clock Battery Cover from the back of
Interior Frame. Locate used battery on the left side of circuit board. Remove used battery by pulling it out of the slot. Insert good battery with positive
(+) side facing the right side of the battery slot. Make sure battery is fully inserted. Reinsert Battery Cover and push to snap into place. Reattach
Interior Frame to wall.
to install power adaptor:
The Cat Flap is supplied with a low-voltage AC adapter for power. Insert
Power Adaptor into Concealed Power Connection located underneath bottom of Interior Frame.
An optional rechargeable lithium-ion battery is available to use with the Cat Flap (sold separately). If using
the Passport
™
Rechargeable Battery instead of adapter for power source, insert it into Battery Compartment
on right side of Interior Frame (see Passport
™
Rechargeable Battery
Operating Guide
for how to install the
rechargeable battery).
Understanding motion Sensors
note:
For testing purposes, the Motion Sensor Wire should have been connected from the Interior Frame to Exterior Frame at the factory. Before
proceeding with the next steps, make sure the Motion Sensor Wire is connected or the Cat Flap will not detect the microchip and open from the
outside during testing (See “Installation In a Non-Glass Door” Step 4F for connecting Motion Sensor Wire).
It is important to understand how the interior and exterior Motion Sensors work and keep this in mind when selecting your installation location.
When the Motion Sensors detect movement, they trigger the reader (which detects and reads the microchip or Passport
™
Key) to turn on. The areas
where the Motion Sensors can detect motion are called the Motion Sensing Zones. Where your cat is detected within the Motion Sensing Zones can
depend on your cat’s size and hair type, surrounding temperatures, and the location where the Cat Flap is installed. For example, if your cat has
longer hair, it may take longer for the Motion Sensors to detect your cat. Also, if your Cat Flap is installed in a location with stairs on one side, the
Motion Sensor will detect your cat differently on the side with the stairs than on the side without the stairs. Blind Zones are areas where the Motion
Sensors cannot detect your cat and the Cat Flap will not read your cat’s microchip or Passport
™
Key.
Check for radio-frequency Interference
Prior to installation, it is recommended to set-up, program and test the Cat Flap in the intended installation location or application to check for
possible Radio-Frequency Interferences. These interferences could negatively affect the Cat Flap, keeping it from working properly and receiving
the signal of the microchip. Common household appliances and electronic products should be located at least 61cm away from the location where
the Cat Flap will be installed. Typical household products to consider are microwaves, televisions, wireless telephones, computers, garage door
openers and hand-held electronic devices such as remote controls or game stations.
Select Installation Location
The Cat Flap must be installed in a location where the LCD Screen, Battery Compartment and Power Adaptor are not exposed to outside elements
such as rain or snow. The Power Adaptor is for inside use only. It is recommended to install the Cat Flap in a location where prolonged exposure to
direct sunlight is not a factor. Cat Flap operating temperature range is: -20.5° C to 55° C.
Go to location where you plan to install the Cat Flap. Place the Cat Flap directly in front of door or desired installation location in the upright
position. Make sure the Cat Flap is vertical and not leaning so flap will operate properly. If using supplied Power Adaptor, find closest power outlet.
Plug in adapter to power the Cat Flap. The Power Adaptor cord is 1.8 m in length. If Power Adaptor cord will not reach closest outlet, you will need
a power cord extension, or to use the optional Passport
™
Rechargeable Battery (both sold separately) or find an alternative location to install the
Cat Flap.
Keep the Cat Flap in front of the door or application in the upright, vertical position and proceed to “Initial User Setup”, “Program Pet” and “Test
Microchip” steps to continue to check for Radio-Frequency Interferences and check the Motion Sensors.
notICe
•The unit only operates properly while outside temperature is greater than -20.5°C and less than 55°C. If operating from optional
rechargeable lithium-ion battery, the battery and Battery Compartment cannot be exposed to temperatures below 0°C.
•Do not install in a location where the Interior Frame, including the LCD Screen and Battery Compartment, and the Power Adaptor are
exposed to damp or wet conditions or to water or outside elements, such as rain or snow.
•Do not use Power Adaptor in temperatures below 0° C or above 40° C. Power Adaptor for inside use only.
•To avoid tripping, always position the power cord out of the path of foot traffic.
