Quick-Start Guide
Part No. 81-9059-0647-0 Rev. B
I
NTEGRITY
CS S
ERIES
A2HD516 P
ROCESSOR
M
ENU
T
REE
C
ONTINUED ON
N
EXT
P
AGE
7
Step
B
ASIC
O
PERATION
(C
ONT
.)
M
ENU
S
CREEN
A
CCESS
C
ODE
Certain menus are password protected. When a
protected menu is accessed, password entry
screen is displayed, as shown at right.
Use rotary knobs to set four highlighted digits to
0999
, as shown.
Press
TAKE
to enter password and access
desired configuration menu screen.
U
SING
S
IDE
C
OLUMN
K
EYER
(I
F
D
ESIRED
)
8
Step
Your A2HD516 Processor is shipped from the factory with the
UDC
operating mode selected.
This mode allows the processor to function as an analog or SD-SDI to HD converter
WITHOUT
using the included side column keyer function.
To use the side column keyer, you MUST provide an HD keyer input video signal and change
the processor to the
UCP
operating mode.
NOTE
If
UCP
is selected as the operating mode and an HD signal is not applied to
the key video input connector, the A2HD516
WILL NOT
function properly!!
C
ONFIGURING
A2HD516
FOR
S
IDE
C
OLUMN
K
EYING
Connect the keyer video source to the Input (IN) 1 BNC on the rear panel of the format
converter module as shown below. This video source must be an HD signal.
Access the Change Mode function from the
Video Configuration menu as directed in the
A2HD516 Video Configuration command listing
of the Menu Tree Reference portion of this guide.
Access to the Change Mode function is password
protected, as shown at right.
Use rotary knobs to set four highlighted digits to
0999
, as shown.
Press
TAKE
to enter password and access
Change Mode menu screen.
Rotate the Select (
Sel
) control (A1) until the
“Switch to UCP” option is displayed, as shown.
Press
TAKE
to reboot the processor and change
operating mode of processor.
If you wish to return to UDC mode, access
Change Mode and select the “Switch to UDC”
option and press
TAKE
to change operating
mode.
SIDE
COLUMN
KEYER
VIDEO INPUT
K
EYER
V
IDEO
I
NPUT
(F
ORMAT
C
ONVERTER
M
ODULE
)
IN 1
OUT 1A
OUT 1B
OUT 2A
OUT 2B
OPTION B
OPTION A
GENLOCK
IN 2
A2HD516 V
IDEO
C
ONFIGURATION
V
IDEO
C
ONFIGURATION
M
ENU
S
CREEN
Video configuration menus and sub-menus are
accessed through the Video Config screen, as
shown to right.
Use
SEL
knob to highlight desired menu entry, as
shown.
Press
MENU
to select desired configuration menu
screen.
Follow menu tree screen and command listings
below
M
ENU
T
REE
R
EFERENCE
T
HIS PORTION OF THE
A2HD516 Q
UICK
S
TART
G
UIDE PROVIDES A LISTING
,
INDENTED
BY LEVEL
,
OF ALL MAIN AND SUB MENUS AND THE ASSOCIATED COMMANDS FOR VIDEO
AND AUDIO CONFIGURATION FUNCTIONS OF THE PROCESSOR
.
Video
{Video Config}
Proc Controls (A1 – Hue, A2 – Gain, A3 – Black, A4 – Chroma)
Hue (A1 to adjust setting)
Gain (A2 to adjust setting)
Black (A3 to adjust setting)
Chroma (A4 to adjust setting)
Color Corrector
White Balance
Red (A2 to change value)
Green (A3 to change value)
Blue (A4 to change value)
Black Balance
Red (A2 to change value)
Green (A3 to change value)
Blue (A4 to change value)
Gamma Balance
Red (A2 to change value)
Green (A3 to change value)
Blue (A4 to change value)
Black
Blk Stretch (A2 to change value)
Blk Lvl (A3 to change value)
CC Memory Save
Mem Bank (A2 to select desired memory location)
Press TAKE to save settings to memory location
CC Memory Recall
Mem Bank (A2 to select desired memory location)
Press TAKE to recall settings from memory location
Input Select
Input Sel
Input 1,2 (A1 to select desired setting)
OnVidLoss
Off, Black (A2 to select desired setting)
Anlg-SD Select
SDI, Analog-A, Analog-B (A1 to select desired setting)
Output
{Output Config}
Primary Output
Format
A1 to select desired video format from listing
Freeze Frame
Frame, Field 1, Field 2 (A2 to select desired setting)
TAKE to set Aspect Ratios
UC-AspRatio
A1 to change value
DC-AspRatio
A1 to select desired setting
DC-AR TrimH
A1 to change value
DC-AR TrimV
A1 to change value
Sec Asp Ratio
4X3-Crop, 4X3-Squeeze, 16X9-Lbox
A1 to select desired setting
HD Config
{HD Config}
HD CloCap
Off, On (A1 to select desired setting)
HD TimeCode
Off, On (A1 to select desired setting)
{HD Timing}
HD H Phase
A1 to change value
HD V Phase
A1 to change value
HD H Video Pos
A1 to change value
HD V Video Pos
A1 to change value
SD Config
{SD Config}
SD CloCap
Off, On (A1 to select desired setting)
Translate Timecode
Off, On (A1 to select desired setting)
SD Legalizer
Luma Limit
Off, Loose, Nominal, Tight
A1 to select desired setting
Encoded Limit
Off, Loose, Nominal, Tight
A1 to select desired setting
RGB Limit
Off, Loose, Nominal, Tight
A1 to select desired setting
VBI Legalizer
Is Off, Follows Main
A1 to select desired setting
