Quick-Start Guide
Part No. 81-9059-0647-0 Rev. B
I
NTEGRITY
CS S
ERIES
A2HD516 P
ROCESSOR
M
ENU
T
REE
R
EFERENCE
(C
ONT
.)
M
ENU
T
REE
C
ONTINUED ON
N
EXT
P
AGE
Eng Config
Password Prompt Screen
Use A1, A2, A3, A4 to select “0999”
Press TAKE to proceed to Eng Config screens
{Engineering Cnfgs}
Frame Config
Set Frame IP
A1 moves cursor left and right to select digit to change
A2 to change value of highlighted digit
Reboot Frame
Password Prompt Screen
Use A1, A2, A3, A4 to select “0999”
Press TAKE to initiate frame reboot
Status
Status display of frame operating parameters
Press TAKE to refresh
{Module1 Cnfgs}
Vid Processing
Full YUV Gamut
ON, Off (A1 to select desired setting)
Press TAKE to advance to next menu
NoiseReduce
On, Off (A1 to select desired setting)
NR Level
A1 to change value
Detail Enh
A1 to change value
{Module2 Vid Cnfgs}
Test Patterns
Test Pattern (A1 to select desired test pattern from listing)
Dynamic Filters
En/Dis (Press TAKE to enable/disable dynamic filter)
Coring (A1 to change value)
Luma Filter
Wide, Soft, Shaped, Dynamic (A2 to select desired setting)
Chr Filt
Flat, Shaped Dynamic, Flat Dynamic (A3 to select desired
setting)
Averaging
Off, Forced, High, Medium, Low (A4 to select desired setting)
Video-In Proc
Hue (A1 to adjust setting)
Gain (A2 to adjust setting)
Black (A3 to adjust setting)
Chroma (A4 to adjust setting)
{Analog In Config}
Comb Mode
Off, Line Adaptive, Frame Adaptive, Normal
A1 to select desired setting
Comb Sensitivity
Frame In-Ph (A1 to change value)
Frame Out-Ph (A2 to change value)
Line In-Ph (A3 to change value)
Line Out-Ph (A4 to change value)
Video TBC
Off, On, Auto (A1 to select desired setting)
Video AGC
Off, On (A1 to select desired setting)
{Additional Config}
Video Standard
Displays current operating video standard: NTSC/525 or PAL/625
Press TAKE to toggle between NTSC and PAL standards
Video Timing
Genlock
Genlock Status
Genlock Source Status Display (OK)
Genlock Source
Frame Connector, Board Connector
A1 to select desired source
Genlock Timing
V Phase (A1 to change value)
H Phase (A2 to change value)
Video Pos
H Video Pos
A1 to set desired position
V Video Pos
A1 to set desired position
Freeze Mode
Frame, Field 1, Field 2 (A1 to select desired setting)
Configure VBI
Config Line/Field
10/1, 10/2….22/1, 22/2 (A1 to select desired setting)
Signal
A2 to select desired signal type from listing
Setup
0.0, 7.5 IRE (A3 to select desired setting)
Comb
Off, On (A4 to select desired setting)
User Reset
Press TAKE to initiate User Reset
{SD Timing}
SD H Phase
A1 to change value
SD V Phase
A1 to change value
SD H Pos
A1 to change value
SD V Pos
A1 to change value
Genlock Source
Frame Connector, Board Connector
A1 to select desired source
Frame Rate
A1 to select desired frame rate setting
Test Pattern
A1 to select desired test pattern output from listing
Encoder Mode
On, Test Bars, Off (A1 to select desired setting)
Noise Reduction
Recursive Filter
Off, Auto, High, Low (A1 to change value)
Measured SNR (display)
Hot Switch
A1 to select desired Hot Switch action from listing
Status and Alarms
OvrTempThr
Over Temperature Alarm Threshold (A1 to change value)
Error Secs
Press TAKE to reset error seconds display
User Reset
Press TAKE to initiate User Reset
Change Mode
Password Prompt Screen
Use A1, A2, A3, A4 to select “0999”
Press TAKE to proceed to Change Mode screen
Change Mode
UDC, UCP (A1 to select desired setting)
Press TAKE to toggle mode selection
Info
Module 1 Info
Displays operational parameters for selected module
Frame Info
Displays operational parameters for chassis frame
