Perkins 2806J-E18TTA Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 100

Perkins 2806J-E18TTA Скачать руководство пользователя страница 80

Test the Service Indicator

Service indicators are important instruments.

• Check for ease of resetting. The service indicator

should reset in less than three pushes.

• Check the movement of the service indicator core

when the engine is run at full load speed. The core
should latch approximately at the greatest vacuum
that is attained.

If the service indicator does not reset easily, or if the
core does not latch at the greatest vacuum, the
service indicator should be replaced. If the new
service indicator will not reset, the hole for the service

indicator may be plugged.

If necessary, replace the service indicator more
frequently in environments that are severely dusty.
Replace the service indicator annually regardless of
the operating conditions. Replace the service
indicator when the engine is overhauled, and
whenever major engine components are replaced.

Note:

When a new service indicator is installed,

excessive force may crack the top of the service
indicator. Tighten the service indicator to a torque of
2 N·m (18 lb in).

i07819538

Engine

Mounts

-

Inspect

Note:

The

engine

mounts

may

not

have

been

supplied

by

Perkins.

Refer

to

the

Original

Equipment

Manufacturer

(OEM)

information

for

further

details

on

the

engine

mounts

and

the

correct

bolt

torque.

Inspect

the

engine

mounts

for

deterioration

and

for

correct

bolt

torque.

Excessive

engine

vibration

can

be

caused

by

the

following

conditions:

• Incorrect mounting of the engine

• Deterioration of the engine mounts

• Loose engine mounts

Any engine mount that shows deterioration should be
replaced. Refer to the OEM information for the
recommended torques.

When the engine mounts are supplied by Perkins the
maintenance procedure will be supplied in the
Disassembly and Assembly manual for your engine.

i07833463

Engine

Oil

Level

-

Check

Hot oil and hot components can cause personal
injury. Do not allow hot oil or hot components to
contact the skin.

Illustration 46

g06451621

Typical example

(1) Oil filler cap
(2) Oil level gauge (Dipstick)

Illustration 47

g00110310

Partial view of the oil level gauge

(Y)

“

ADD

”

mark

(X)

“

FULL

”

mark

NOTICE

Perform this maintenance with the engine stopped.

80

M0109073

Maintenance Section
Engine Mounts - Inspect

«
...
78
79
80
81
82
...
»

Содержание 2806J-E18TTA





































































































Отзывы:

Нет отзывов