Perkins 2806J-E18TTA Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 100

Perkins 2806J-E18TTA Скачать руководство пользователя страница 72

Thoroughly rinse the battery case with clean
water.

i05424317

Battery

or

Battery

Cable

-

Disconnect

The battery cables or the batteries should not be
removed with the battery cover in place. The bat-
tery cover should be removed before any servic-
ing is attempted.

Removing the battery cables or the batteries with
the cover in place may cause a battery explosion
resulting in personal injury.

1.

Turn the start switch to the OFF position. Turn the

ignition switch (if equipped) to the OFF position
and remove the key and all electrical loads.

Note:

After the engine has stopped, allow 2 minutes

in order for the diesel exhaust fluid lines to be purged
before disconnecting the power.

2.

Disconnect the negative battery terminal. Ensure

that the cable cannot contact the terminal. When
four 12 V batteries are involved, 2 negative
connections must be disconnected.

3.

Remove the positive connection.

4.

Clean all disconnected connection and battery

terminals.

5.

Use a fine grade of sandpaper to clean the

terminals and the cable clamps. Clean the items
until the surfaces are bright or shiny. DO NOT
remove material excessively. Excessive removal
of material can cause the clamps to fit incorrectly.
Coat the clamps and the terminals with a suitable
silicone lubricant or petroleum jelly.

6.

Tape the cable connections in order to help

prevent accidental starting.

7.

Proceed with necessary system repairs.

8.

In order to connect the battery, connect the

positive connection before the negative connector.

i07831569

Belts

-

Inspect/Adjust/Replace

Illustration 39

g06450720

Typical example

(1) Belt
(2) Tensioner
(3) Square drive

Inspect

To maximize the engine performance, inspect the
belt for wear and for cracking. Replace the belt if the
belt is worn or damaged.

• Inspect the belt for cracks, splits, glazing, grease,

displacement of the cord and evidence of fluid
contamination.

The belt must be replaced if the following conditions
are present.

• The belt has a crack in more than one rib.

72

M0109073

Maintenance Section
Battery or Battery Cable - Disconnect

«
...
70
71
72
73
74
...
»

Содержание 2806J-E18TTA





































































































Отзывы:

Нет отзывов