Perkins 2806J-E18TTA Скачать руководство пользователя страница 21

Страница: 21 / 100

Illustration 16

g06451722

Typical example

(1) Exhaust inlet
(2) Aftertreatment identification device

(3) Clamps
(4) Exhaust outlet

(5) DOC mounting points

i07833367

Product

Description

The

Perkins

2806J-E18TTA

Industrial

Engine

has

the

following

characteristics:

• Four-stroke cycle

• Mechanically actuated, electronically controlled

fuel injection system

• Two Turbochargers

• Air to air charged cooled

• Aftertreatment system

The Clean Emissions Module (CEM) consists of
Diesel Oxidation Catalyst (DOC).

Engine Specifications

Note:

The front end of the engine is opposite the

flywheel end of the engine. The left and the right
sides of the engine are determined from the flywheel
end. The number 1 cylinder is the front cylinder.

Illustration 17

g01387009

Cylinder and valve location

(A) Exhaust valve
(B) Inlet valve

Table 1

Engine Specifications

Engine

2806J

Arrangement and Cylinders

In-Line 6 cylinder

Bore

145 mm (5.7 inch)

Stroke

183 mm (7.2 inch)

Aspiration

ATAAC

(1)

(continued)

M0109073

Product Information Section

Product Description

Содержание 2806J-E18TTA




































































































Результаты поиска

Содержание 2806J-E18TTA

Отзывы:

Perkins 2806J-E18TTA, Руководство по эксплуатации и обслуживанию, Страница: 21 / 100

Результаты поиска

Содержание 2806J-E18TTA

Отзывы: