Perkins 1106A-70T Скачать руководство пользователя страница 53

Страница: 53 / 58

Rotate the crankshaft by hand in order to ensure

that the crankshaft is not stuck. Check the oil
viscosity and any external loads that could affect
the engine rotation.

If the crankshaft is stuck or difficult to turn,
repair the engine.

If the engine is not difficult to turn, go to Step 6.

Attempt to crank the starting motor.

The starting motor cranks slowly.

Remove the starting motor for repair or
replacement.

The starting motor does not crank.

Check for the blocked engagement of the
pinion gear and flywheel ring gear.

Note:

Blocked engagement and open solenoid

contacts will give the same electrical symptoms.

i02404376

Glow

Plugs

Test

Continuity Check of the Glow Plugs

The following test will check the continuity of the glow
plugs.

Disconnect the power supply and the bus bar.

Use a suitable digital multimeter to check continuity

(resistance). Turn the audible signal on the digital
multimeter ON.

Place one probe on the connection for the glow

plug and the other probe to a suitable ground. The
digital multimeter should make an audible sound.
Replace the glow plug if there is no continuity.

Check the continuity on all the glow plugs.

Checking The Operation of The
Glow Plug

The following test will check the operation of the glow
plugs.

Disconnect the power supply and the bus bar.

Connect the power supply to only one glow plug.

Place a suitable ammeter on the power supply

wire.

Connect a suitable digital multimeter to the terminal

on the glow plug and to a suitable ground.

Turn the switch to the ON position in order to

activate the glow plugs.

Table 15

12 Volt System

Amp

Time (sec)

16.6

Initial

5.7

11.1

Table 16

24 Volt System

Amp

Time (sec)

Initial

3.3

5.3

Check the reading on each of the glow plugs.

If there is no reading on the ammeter check the

electrical connections. If the readings on the
ammeter are low replace the faulty glow plug. If
there is still no reading replace the faulty glow plug.

i04538676

V-Belt

Test

Table

Required Tools

Tool

Part Number

Part Description

Qty

Belt Tension Gauge

UENR0617

Electrical System

This document has been printed from SPI2. NOT FOR RESALE.

Содержание 1106A-70T


























































Результаты поиска

Содержание 1106A-70T

Отзывы:

Perkins 1106A-70T, Руководство по эксплуатации, Страница: 53 / 58

Результаты поиска

Содержание 1106A-70T

Отзывы: