PerkinElmer Frontier FT-IR Скачать руководство пользователя страница 74

Страница: 74 / 100

74 . Frontier IR Single-range Spectrometers User's Guide

Replacing the Source

WARNING

Switch off the mains power supply to the spectrometer, wait

60 seconds and disconnect the power cable before you open the cover of

the spectrometer. This makes sure that you are safe from electrical shock

and laser radiation.

WARNING

Due to its high operating temperature allow sufficient time for the source

to cool before attempting to remove it.

Open the main cover of the instrument as detailed on page 70 and identify the source

(Figure 41).

Figure 41 Source location

Caution, hot surface.

The source housing and source itself will be hot if recently switched on.

Allow to cool before performing the following procedure.

CAUTION

The source element is brittle and can be broken if not handled properly.

Be careful when removing and installing the source.

Do not touch the glass bulb as this will degrade the performance of the

bulb and shorten its life.

Source

Содержание Frontier FT-IR





































































































Результаты поиска

Содержание Frontier FT-IR

Отзывы:

Похожие инструкции для Frontier FT-IR

Бренды по названию

Популярные бренды

PerkinElmer Frontier FT-IR, Руководство пользователя

Результаты поиска

Содержание Frontier FT-IR

Отзывы:

Похожие инструкции для Frontier FT-IR

Бренды по названию

Популярные бренды