background image

To prevent injury to the user or other people and property damage, the following instructions 
must be followed. Incorrect operation due to ignoring of instructions may cause harm or 
damage. The seriousness is classified by the following indications.

Safety Precautions

This symbol indicates the possibility of death or serious injury.

Meanings of symbols used in this manual are as shown below.

!

!

WARNING

Always do this.

Never do this.

!

CAUTION

This symbol indicates the possibility of injury or damage to property.

Plug in power plug 
properly.

Do not modify power cord
length or share the outlet
with other appliances. 

Always ensure effective
grounding.

Unplug the unit if strange
sounds, smell, or smoke
comes from it.

Keep firearms away.

Ventilate room before operating air
conditioner if there is a gas leakage from
another appliance.

   Otherwise, it may cause electric
   shock or fire due to excess heat 
   generation.

  It may cause electric shock or 
  fire due to heat generation.

  Incorrect grounding may cause 
  electric shock.

  It may cause fire and electric
  shock.

  It may cause fire.

  It may cause explosion, fire and, burns.

  It may cause electric shock or fire
  due to heat generation.

  It may cause electric shock.

  It may cause failure of machine
  or electric shock.

  It may cause fire and electric 
  shock.

  It may cause fire and electric 
  shock.

  It may cause electric shock or fire.
  If the power cord is damaged, it 
  must be replaced by the manufac-
  turer or an authorized service 
  center or a similarly qualified per-
  son in order to avoid a hazard.

  This could damage your health.

  Incorrect installation may cause 
  fire and electric shock.

  It may cause electric shock.

   It may cause an explosion or fire.

  It may cause failure and electric shock.

Do not operate or stop the unit 
by inserting or pulling out the 
power plug directly from the wall

.

Do not operate with wet
hands or in damp 
environment.

Do not allow water to run
into electric parts.

Do not use the socket if it is
loose or damaged.

Do not use the power cord
close to heating appliances.

Do not damage or use an 
unspecified power cord.

Do not direct airflow at 
room occupants only.

Always install circuit
breaker and a dedicated
power circuit.

Do not open the unit
during operation.

Do not use the power cord near 
flammable gas or combustibles, such
as gasoline, benzene, thinner, etc.

Do not disassemble or modify, or drill 
holes into the air conditioner.

!!

!!

!!

!!

!!

WARNING

!

2

!!

!!!!

 

Содержание 12.000 BTU




























Отзывы: