background image

TTD-03.1 Electromechanical Box Tripod Turnstile 

13 

The remote indicators can be connected to the connector blocks “XT4”

 

(“Light A”) and “XT5” (“Light 

B”). At that the “Light A”

 

(“Light B”) relay is active (the voltage is supplied to relay coil), when the 

“Green arrow” pictogram on the indication module (4) corresponding to the set passage direction 

lights, and it is normalized, when the “Green arrow” pictogram on the indication module (4) does 

not light.

 

The response/trip of relays “Light A” and “Light B” can be defined according to lighting 

up/going down of the red indicators, which are installed near the above mentioned relays (see 

Fig. 4). Output cascades for “Light A” and “Light B” are nonbridging relay contacts (see Fig. 8) with 

the following signal characteristics: 

  maximum DC switched voltage ..................................................................................... 30 V 

  maximum AC switched voltage .................................................................................... .42 V 

  maximum switched AC/DC .............................................................................................. 3 A 

  closed contact resistance .............................................................................. max 0.15 Ohm 

 

Fig.8 Output cascades for Light A and Light B 

5.5  Operation contingencies and response 

The turnstile is capable to provide information on the following operation contingencies: 

  unauthorized access; 

  passage delay for more than 30 sec; 

  one or both optical sensors of arm rotation out of order.  

A special signal “Ready” is formed in each of the above case.  
In case of unauthorized access signal “Ready” is formed as follows. At arm rotation at 8° one of the 

optical sensors responds and the output contacts “Ready” and “Common” get broken (beginning of 

the signal). When the barrier arms reset into initial state the both optical sensors become 

normalized and the output contacts “Ready” and “Common” get closed (finish of the signal). 
In case of delay of an authorized passage for more than 30 seconds the signal “Ready” is formed 

as follows: If within 30 seconds from the moment of passage commencing, which is determined by 

the arm rotation at not less than 8° (i.e. activation of one of the optical sensors), the reset of barrier 

arms to the initial state does not happen, the output contacts “Ready” and “Common” break 

(beginning of the signal). When the barrier arms reset to the initial state the both optical sensors 

are normalized and the output contacts Ready and Common are closed (finish of the signal). 
When one or both of the optical sensors are out of order the output contacts “Ready” and 

“Common” are broken (beginning of the signal “Ready”). After elimination of the fault the closed 

status of contacts “Ready” and “Common” is renewed. 

6  MARKING AND PACKAGING 

Marking of the turnstile is made in form of a label and sticker. 
The label is located inside, on the rear panel of the turnstile housing. To get access to the label, 

remove the turnstile cover (3) by unlocking the turnstile cover lock (6) with the key and turning it 

clockwise up to the stop (the lock cylinder moves out of the case). Shift the cover to the right up to 

the stop (slight push is allowed). Lift the cover and carefully remove it. Be careful! The indication 

modules (4), located on the turnstile cover are connected to the control device with cables, which 

must be disconnected before taking the cover off. Place the turnstile cover on a steady and level 

Содержание TTD-03.1































Отзывы: