background image

Operation manual 

26 

Appendix 

А

 Control signal algorithm at pulse control mode 

 

Note! For the RC-panel: 

  active front — pressing of the relevant button on the RC-panel; 

  low level — the relevant button on the RC-panel has been pressed; 

  high level — the relevant button on the RC-panel has not been pressed. 

The following commands can be formed by sending a low-level signal to the contacts “Unlock A”, 

“Stop” and “Unlock B” of the “XT1.L” connector block relatively to the contact “GND” (The 

command is a signal active front (signal transfer from the high level to the low level) at any of the 

contacts at presence of the corresponding signal levels at the other contacts): 

Always locked (closed for entry and exit) - 

Active front is at contact “Stop” while there is a high level at contacts “Unlock A” and “Unlock B”. 
Both passage directions get closed at this command. 

Single passage in direction А (open for passage of one person in direction А) 

Active front is at contact “Unlock A” while there is a high level at contacts “Stop” and “Unlock B”. 

At this command passage direction А opens either for 5 sec. or until the passage has been made 

in this direction or until the command 

«Always  locked»

,  and  the  status  of  passage  direction  В 

does not change. The command is ignored if at the moment of its receipt the status of passage 

direction А was 

«Always free»

Single passage in direction В (open for passage of one person in direction В) 

Active front is at contact “Unlock B” while there is a high level at contacts “Stop” and “Unlock A”. 
At this command passage direction B opens either for 5 sec. or until the passage has been 

effected in this direction or until the command 

«Always

 

locked»

, and  the status of passage 

direction A does not change. The command is ignored if at the moment of its receipt the status of 

passage direction B was 

«Always free»

Single passage in both directions (open for single passage of one person at a time in each 

direction) - 

Active front is at contact “Unlock A” while there is a low level at contact “Unlock B” and a high level 

at contact “Stop”, 
or active front is at contact “Unlock B” while there is a low level at contact “Unlock A” and a high 

level at contact “Stop”. 
At this command the both passage directions open either for 5 sec. each or until the command 

«Always locked»

 is received. The command is ignored for the passage direction, which status at 

the moment of its receipt was 

«Always free»

Free passage in direct

ion А (open for free passage in direction А) 

Active front is at contact “Unlock A” while there is a low level at contact “Stop” and a high level at 

contact “Unlock B”, 
or active front is at contact “Stop” while there is a low level at contact “Unlock A” and a high level at 

contact “Unlock B”. 

At this command passage direction А opens until the command 

«Always locked» 

is received and 

the status of passage direction В does not change.

 

Free passage in direction В (open for free passage in direction В) 

Active front is at contact “Unlock B” while there is a low level at contact “Stop” and a high level at 

contact “Unlock A”, 
or active front at contact “Stop” while there is a low level at contact “Unlock B” and a high level at 

contact “Unlock A”. 
At this comman

d passage direction В opens until the command 

«Always locked» 

is received and 

the status of passage direction А does not change.

 

Free passage (open for passage in both directions) - 

Active front is at contact “Unlock A” while there is a low level at contacts “Unlock B” and “Stop”, 
or active front is at contact “Unlock B” while there is a low level at contacts “Unlock A” and “Stop”, 
or active front is at contact “Stop” while there is a low level at contacts “Unlock A” and “Unlock B”. 
The both directions open at this command until the command 

«Always locked» 

is received. 

Содержание TTD-03.1































Отзывы: