Pepwave MAX 700 страница 119 Скачать руководство пользователя | Manualshive

Страница: 119 / 404

background image

When

Use the following DNS server address(es)

is selected, you may enter

custom DNS server addresses for this WAN connection into the

DNS Server

1

and

DNS Server 2

fields.

IP Passthrough

When this

IP Passthrough

option is active, after the ethernet WAN connection

is up, the router's DHCP server will offer the connection's IP address to one
LAN client. All incoming or outgoing traffic will be routed without NAT.

Regardless the WAN connection's state, the router always binds to the LAN IP
address (Default: 192.168.50.1). So when the ethernet WAN is connected, the
LAN client could access the router's web admin by manually configuring its IP
address to the same subnet as the router's LAN IP address (e.g.
192.168.50.10).

Note: when this option is firstly enabled, the LAN client may not be able to
refresh its IP address to the ethernet WAN IP address in a timely fashion. The
LAN client may have to manually renew its IP address from DHCP server. After
this option is enabled, the DHCP lease time will be 2 minutes. I.e. the LAN
client could refresh its IP address and access the network at most one minute
after the ethernet WAN connection goes up.

Independent from

Backup WANs

If this is checked, the connection will be working independent from other
Backup WAN connections. Those in

Backup Priority

will ignore the status of

this WAN connection, and will be used when none of the other higher priority
connections are available.

Standby State

This option allows you to choose whether to remain connected when this WAN
connection is no longer in the highest priority and has entered the standby
state. When

Remain connected

is chosen, upon bringing up this WAN

connection to active, it will be immediately available for use.

If this WAN connection is charged by connection time, you may want to set this
option to

Disconnect

so that connection will be made only when needed.

PepVPN may use connected standby WAN for failover if link failure detected
on the higher priority WAN, you can set this option to Disconnect to avoid data
passing through.

Reply to ICMP

PING

If the checkbox is

unticked

, this option is disabled and the system will not reply

to any ICMP ping echo requests to the WAN IP addresses of this WAN
connection.

Default:

ticked

(Yes)

Upload Bandwidth

This field refers to the maximum upload speed.

This value is referenced when default weight is chosen for outbound traffic and
traffic prioritization. A correct value can result in effective traffic prioritization
and efficient use of upstream bandwidth.

«
...
117
118
119
120
121
...
»

Содержание MAX 700





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAX 700

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

Бренд: Rain Bird Страницы: 17

Бренд: Danfoss Страницы: 61

Бренд: X-Micro Страницы: 74

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

Бренд: B&B Electronics Страницы: 2

AirStation WZR-1166DHP

Бренд: Buffalo Страницы: 2

Бренд: VERTO Страницы: 48

GigaVUE H TA100-CXP

Бренд: Gigamon Страницы: 115

Бренд: ACTi Страницы: 12

Бренд: Avaya Страницы: 2

Бренд: Comtrend Corporation Страницы: 69

Бренд: AMCI Страницы: 55

DHI-NVR5208-4KS2

Бренд: Dahua Страницы: 361

Бренд: Dahua Страницы: 489

Бренд: Billion Страницы: 183

Бренд: RadioLabs Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды