Pentair Sta-rite EnviroMAX 1500, Инструкция по установке, эксплуатации и обслуживанию

Страница: 18 / 28

Factory Reset
The drive can be reset to factory settings if necessary. A Factory Reset will wipe out all of the saved
user settings that have been programmed, except for the time of day. Be sure that it is necessary before
performing a Factory Reset, as the results are immediate.
To perform a Factory Reset:
1. Stop the pump if necessary by pressing the Start/Stop button.
2. Record all of the custom schedule settings using Table 3. You can find these setting by pressing the
“ 1 ”, “ 2 ”, “ 3 ”, and “ Quick Clean ” buttons and cycling through all the screens. Also write down the Priming
Speed.
3. Press and hold the “ 1 ”, “ 2 ”, “ 3 ”, and “ Quick Clean ” buttons for 3 seconds.
4. The screen will display “FACt rSt” if factory reset is successful. See Figure 9 .
5. Be sure to reprogram the schedule and priming speed after the factory reset. The pump must be turned
back on with the Start/Stop button before it will run again. The pump will run the programmed schedule
upon initial start-up.
Note: Factory Reset can not be performed from a Keypad Lockout state.
12
SUPERFLO
®
VS Variable Speed Pump Installation and User’s Guide
Factory Reset
The drive can be reset to factory settings if
necessary. A Factory Reset will wipe out all of the
saved user settings that have been programmed,
except for the time of day. Be sure that it is
necessary before performing a Factory Reset, as the
results are immediate.
To perform a Factory Reset:
1. Stop the pump if necessary by pressing the
Start/Stop
button.
2. Record all of the custom schedule settings using
Table 3
. You can find these setting by pressing
the “
1
”, “
2
”, “
3
”, and “
Quick Clean
” buttons and
cycling through all the screens. Also write down
the Priming Speed.
3. Press and hold the “
1
”, “
2
”, “
3
”, and “
Quick
Clean
” buttons for 3 seconds.
4. The screen will display “ FACt rSt ” if factory
reset is successful. See
Figure 13
.
5. Be sure to reprogram the schedule and priming
speed after the factory reset. The pump must
be turned back on with the
Start/Stop
button
before it will run again. The pump will run the
programmed schedule upon initial start-up.
Note
: Factory Reset can not be performed from
a Keypad Lockout state.
Speed
(RPM)
Duration
(Hours)
Start Time
(Time Clock)
SPEED 1
SPEED 2
SPEED 3
QUICK
CLEAN
Priming
Speed
Table 3: User Programmed Schedules
Figure 9: Drive Factory Reset
FACt rSt
12
SUPERFLO
®
VS Variable Speed Pump Installation and User’s Guide
Factory Reset
The drive can be reset to factory settings if
necessary. A Factory Reset will wipe out all of the
saved user settings that have been programmed,
except for the time of day. Be sure that it is
necessary before performing a Factory Reset, as the
results are immediate.
To perform a Factory Reset:
1. Stop the pump if necessary by pressing the
Start/Stop
button.
2. Record all of the custom schedule settings using
Table 3
. You can find these setting by pressing
the “
1
”, “
2
”, “
3
”, and “
Quick Clean
” buttons and
cycling through all the screens. Also write down
the Priming Speed.
3. Press and hold the “
1
”, “
2
”, “
3
”, and “
Quick
Clean
” buttons for 3 seconds.
4. The screen will display “ FACt rSt ” if factory
reset is successful. See
Figure 13
.
5. Be sure to reprogram the schedule and priming
speed after the factory reset. The pump must
be turned back on with the
Start/Stop
button
before it will run again. The pump will run the
programmed schedule upon initial start-up.
Note
: Factory Reset can not be performed from
a Keypad Lockout state.
Speed
(RPM)
Duration
(Hours)
Start Time
(Time Clock)
SPEED 1
SPEED 2
SPEED 3
QUICK
CLEAN
Priming
Speed
Table 3: User Programmed Schedules
Figure 9: Drive Factory Reset
FACt
rSt
17
Operation