Pentair Sta-rite EnviroMAX 1500, Инструкция по установке, эксплуатации и обслуживанию

Страница: 16 / 28

Priming will automatically run when the EnviroMAX 1500 Variable Speed Pump is started from a stopped
state, except when running in Quick Clean mode. Priming will run at 3450 RPM by default, and will last for
5 minutes. The drive’s screen will display and cycle through the following things “PrI - Priming Speed, PrI
-- Remaining Time”.
Once priming has begun, the speed can be adjusted between 3450 and 1700 RPM using the “ + ” and “ - ”
arrows. If it is adjusted below 1700 RPM, Priming mode will be disabled and the pump will immediately
begin to run the scheduled speed.
When priming is disabled and the pump is started from a stopped state, the screen will display, “PrI - OFF”
for 10 seconds while running the scheduled speed (See Figure 6 ). This allows the user time to enable
priming mode by pressing the “ + ” arrow. If the user chooses to re-enable priming mode, the pump will
then transition from the scheduled speed to 1700 RPM. The user can increase the priming speed from
1700 RPM by pressing the “ + ” arrow. The 5 minute priming countdown timer starts when priming is first
engaged.
The installer should set the priming speed to be sufficient for priming the pump from a fresh install,
but not so fast that there is a substantial waste of energy during the 5 minute priming window. The time
the pump needs to achieve prime can change based on local environmental conditions such as water
temperature, atmospheric pressure, and your pool’s water level. All of these things should be taken into
consideration when setting the priming speed, however in most cases the pump will not need to run at
3450 RPM to successfully prime itself.
Please test and verify chosen priming speeds more than once, letting the water drain from the system in
between each test.
Note: The pump strainer basket should always remain full to the bottom of the inlet in order to prevent air
from entering the system.
The EnviroMAX 1500 Variable Speed Pump is equipped with a Quick Clean feature, which can be engaged
to temporarily run at higher or lower speeds ranging between 300 to 3450 RPM. Once the Quick Clean
duration has elapsed, the pump will automatically return to the programmed schedule.
Programming Quick Clean:
1. Stop the pump if it is running by pressing the Start/Stop button.
2. Press the Quick Clean button. The LED above the Quick Clean button and the “Speed” parameter LED
will flash while editing. See Figure 7 .
Quick Clean
10
SUPERFLO
®
VS Variable Speed Pump Installation and User’s Guide
This pump is shipped with Priming mode ENABLED. Unless the Priming settings are changed in the menu, be aware
that the pump will speed up to the priming speed when the pump is powered on for the first time, and the
start/stop button is pressed.
Before turning the pump ON, be sure the following conditions are met:
1. Open filter air relief valve.
2. Open valves.
3. Pool return is completely open and clear of any blockages.
4. Water in the pump basket.
5. Stand clear of the filter or other pressurized vessels.
DO NOT run the pump dry. If the pump is run dry, the mechanical seal will be damaged and the pump will start leaking.
If this occurs, the damaged seal must be replaced. ALWAYS maintain proper water level in your pool (half way up
skimmer opening). If the water level falls below the skimmer opening, the pump will draw air through the skimmer, losing the prime and
causing the pump to run dry, resulting in a damaged seal. Continued operation in this manner could cause a loss of pressure, resulting
in damage to the pump case, impeller and seal and may cause property and personal injury.
Priming will automatically run when the SuperFlo
®
VS
Variable Speed Pump is started from a stopped state,
except when running in Quick Clean mode. Priming
will run at 3450 RPM by default, and will last for 5
minutes. The drive’s screen will display and cycle
through the following things “ PrI - Priming Speed,
PrI -- Remaining Time”.
Once priming has begun, the speed can be adjusted
between 3450 and 1700 RPM using the “
+
” and “
-
”
arrows. If it is adjusted below 1700 RPM, Priming
mode will be disabled and the pump will immediately
begin to run the scheduled speed.
When priming is disabled and the pump is started
from a stopped state, the screen will display, “ PrI
- OFF ” for 10 seconds while running the scheduled
speed (See
Figure 10
). This allows the user time to
enable priming mode by pressing the “
+
” arrow. If the
user chooses to re-enable priming mode, the pump
will then transition from the scheduled speed to 1700
RPM. The user can increase the priming speed from
1700 RPM by pressing the “
+
” arrow. The 5 minute
priming countdown timer starts when priming is first
engaged.
The installer should set the priming speed to be
sufficient for priming the pump from a fresh install,
but not so fast that there is a substantial waste of
energy during the 5 minute priming window. The time
the pump needs to achieve prime can change based
on local environmental conditions such as water
temperature, atmospheric pressure, and your pool’s
water level. All of these things should be taken into
consideration when setting the priming speed, however
in most cases the pump will not need to run at 3450
RPM to successfully prime itself.
Please test and verify chosen priming speeds more
than once, letting the water drain from the system in
between each test.
Note
: The pump strainer basket should always remain
full to the bottom of the inlet in order to prevent air from
entering the system.
Figure 6: Priming Deactivation
PrI
OFF
Priming
11
SUPERFLO
®
VS Variable Speed Pump Installation and User’s Guide
Quick Clean
The SuperFlo
®
VS Variable Speed Pump is equipped
with a Quick Clean feature, which can be engaged
to temporarily run at higher or lower speeds ranging
between 300 to 3450 RPM. Once the Quick Clean
duration has elapsed, the pump will automatically
return to the programmed schedule.
Programming Quick Clean:
1. Stop the pump if it is running by pressing the
Start/Stop
button.
2. Press the
Quick Clean
button. The LED
above the
Quick Clean
button and the “Speed”
parameter LED will flash while editing. See
Figure 11
.
3. Use the “
+
” and “
-
” arrows to adjust the speed in
RPM for Quick Clean.
4. Press the
Quick Clean
button again and the
display will change to Quick Clean duration. The
“Duration” parameter LED will flash while editing.
See
Figure 12
.
Note:
The Quick Clean feature does not have a
start time.
5. Use the “
+
” and “
-
” arrows to adjust the duration
in hours and minutes for Quick Clean.
6. Press the
Start/Stop
button and ensure the LED
is illuminated. The pump is now on and will run
the speed and duration set for Quick Clean.
Note:
When the Quick Clean duration ends, the pump
resumes the 24 hour schedule at the point where it
normally would be running at that time. The Quick
Clean duration will not affect the start or stop times
of the 24 hour schedule. For example, if Quick Clean
runs during a period overlapping with a later part of
SPEED 1 and an early part of SPEED 2, the start time
of SPEED 3 is not affected.
Note:
Pressing/Holding Quick Clean key for more than
three (3) seconds will cancel Quick Clean mode.
Note:
During the Quick Clean mode, the pump will not
start with the priming sequence.
Note:
It is recommended that you do not set the Quick
Clean duration to 0 HRS. Setting the Quick Clean
duration to 0 HRS will not allow you to change the
duration setting while the motor is running. The motor
will have to be stopped in order to change the Quick
Clean settings if the duration is set to 0 HRS.
Keypad Lockout
The SuperFlo VS Variable Speed Pump user interface
has a Keypad Lockout feature to prevent unwanted
changes to the settings. When locked, the keypad will
only accept input from pressing the
Display
button to
cycle the displayed information on the screen and input
to stop the motor from a press of
Start/Stop
button.
The keypad can be locked by pressing and holding the
“
1”
button and the
Quick Clean
button at the same time
for at least three seconds. “ Loc On ” will be displayed if
successful.
To unlock the keypad press and hold the “
1
” button and
the
Quick Clean
button at the same time for at least
three seconds. “ Loc OFF ” will be displayed if successful.
Note
: While operating in Keypad Lockout mode the motor
can still be stopped by pressing the
Start/Stop
button.
However, the motor can not be started again until the
user unlocks the keypad.
Key lockout will not prevent the motor from being stopped by pressing
the Start/Stop button. It will then be unable to be restarted until the
keypad has been unlocked. If the motor is operating in Keypad Lockout
mode, and being controlled through external controls, it can only run
when the Start/Stop LED is illuminated.
3450
Figure 7: Setting Speed for Quick Clean
2
:
00
Figure 8: Setting Duration for Quick Clean
15
Operation