Pentair Pool and Spa Control System SunTouch Скачать руководство пользователя страница 19

Страница: 19 / 88

SunTouch Pool and Spa Control System Installation and User’s Guide

SPA/POOL:

Press the SPA (Up

arrow) button to display the current

spa water temperature settings. If the pool filter pump is
switched on from the “Circuit On/Off” menu or a
programmed schedule, “POOL” is displayed with the
current pool water temperature settings. “SPA” and
“POOL” are displayed alternatively if both are active. The
filter pump will switch off while the pool/spa valves are
rotating into position.

For information about

HI-TEMP/LO-TEMP

controls for this button (single body

system) see page 33.

SunTouch Main Status Screen

(Pool/Spa mode - Shared Equipment)

Use the SunTouch display to view daily pool and spa operations. The “Schedule” menu feature (page 17) is
typically used for these operations. For manual spa operation, pressing the SPA Up button will activate the spa
circuit, switch on the filter pump, display the current spa water, air temperature setting, and heat source. To
activate the pool circuit and activate the filter pump, display the current pool water and air temperature, and heat
source, set the menu feature “Circuit On/Off” to “ON.” If the AUX 1 (Down arrow) button is assigned to a light
circuit, use this button to manually switch the lights on/off. Lights and other installed equipment are setup from the
“Circuit Function” menu (page 26). Before using the SunTouch system, familiarize yourself with the status screen
and control buttons.

AIR:

Displays the outside ambient

air temperature via the air sensor

located near the pool area. To display the air
temperature setting, the air sensor must be enabled
(see “Advanced” menu, page 24). The main status screen
toggles between the pool, spa and air temperature
settings. Degree units are displayed in either Fahrenheit
or Celsius. If the top display line displays “SunTouch”, no
spa or pool function is active and air sensor is not
enabled.

SPA 75°F / 85°F

11:51AM HEATER

Spa button:

Switch the spa on

and off and display current
temperature settings. Press
this button to activate the filter
pump and rotate the valves
and circulate pool water to the
spa. To enable heat for the spa
when this circuit is switched
on, either switch on the heat
source or switch on “Manual
Heat” from the “Heat” menu.

AUX 1 button:

Press this

button to manually switch on
the AUX 1 relay (number 1 is
displayed). AUX 1 can be
assign to operate accessory
equipment such as pool and
spa lights.

Note:

For information about

HI-TEMP (UP arrow button)

circuit controls for single body
systems, see page 33.

Lower current set point
temperature setting

HEATER:

Displays the heat source (

Heater, Solar Prf., Solar

)

being used as specified in the “Heat” menu settings (see page
14). If heat is enabled, when the pool filter pump is switch on, the
heat source is displayed.

75° F / 85° F:

Displays the actual spa or pool water temperature

(75° F) and the set point temperature (85° F) as set in the
“Heater” menu (see page 14). To adjust set temperature setting
use the (-) TEMP and (+) TEMP buttons.

Time:

Displays the SunTouch system time as set in the “Clock”

menu setting (see page 19).

AUX 1 2 3:

Displays AUX 1, 2, 3 (lower line)

when these auxiliary relay circuits are

switched on. Press the AUX 1 (

) button to manually switch

auxiliary 1 on or off. AUX 2, and AUX 3 can be switch on and off
manually from the “Circuit On/Off” menu (page 13). Auxiliary
functions are assign in the “Circ. Function” menu (page 26).

AUX D:

“D” indicates the selected circuit

(AUX 1,2,3) is in “delay” mode. For

example, if AUX 2 is assigned to a cleaner, when the auxiliary
circuit 2 is switched on via the “Circuit On/Off” menu setting, this
will force the filter pump on for five (5) minutes before the cleaner
pump switches on. See “Circuit Functions Menu” (page 26) for
more information.

Raise current set point
temperature setting

AIR 77°F FRZ
11: 51AM AUX 1

POOL 75°F / 85°F
11:51AM HEATER

AIR 77°F
11: 51AM AUX D

FRZ:

Indicates the air sensor is

connected and enabled, and
freeze protection is active (see page 26).

AIR 77°F
11: 51AM AUX 123