manualshive.com logo in svg

Pentair MasterTemp 200, Инструкция по установке и эксплуатации

Поделиться
Скачать
Pentair MasterTemp 200 Скачать руководство пользователя страница 33

P/N 474131  Rev. M  8/2020                                                                                                          MasterTemp Pool and Spa Heater              

33

Section 1.    Installation

EXHAUST SIDE

ELECTRICAL
CONDUIT PORT

HEATER BONDING

CONNECTOR

Figure 30.

HEATER BONDING

WARNING

To reduce voltage gradients in the pool area, the 

heater and the pool system equipment must be 

electrically grounded and “bonded” together. Con

-

nect a solid copper conductor (8 AWG or larger) to 

the heater “bonding” terminal lug provided on the 

exhaust side of the heater. 

See Figure 30. 

Not properly “bonding” and grounding the heater 

increases the risk of electrical shock and can cause 

damage and electrolysis to the heat exchanger.

All wiring must be in accordance with all applicable 

codes. The heater, when installed, must be 

electrically grounded and “bonded” in accordance 

with local codes or, in the absence of local codes, 

with the National Electrical Code or the Canadian 

Electrical Code (as applicable). 

Содержание MasterTemp 200





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды