manualshive.com logo in svg

Pentair MasterTemp 200, Инструкция по установке и эксплуатации

Поделиться
Скачать
Pentair MasterTemp 200 Скачать руководство пользователя страница 23

P/N 474131  Rev. M  8/2020                                                                                                          MasterTemp Pool and Spa Heater              

23

NOTE *:

 Vents extending 1.5 m (5 ft) or more 

above the roof must be braced or guyed. Consult 
your local code officials for detailed information.

VENT INSTALLATION – 

INDOOR INSTALLATION OR OUTDOOR SHELTER

Flueing must be in accordance with AS/NZS 5601.1

Always vent the heater to the outdoors, see Note*.

• Vent it vertically using double wall vent connector pipe.

Locate the heater so as to minimize the length of horizontal venting and the number of vent elbows required. Horizontal 

vent runs must slope to allow exhaust condensate to drain and it is recommended to have a condensate drain as described 

in the venting installation instructions.

VERTICAL VENTING

(See Figures 18, 19, and 20)

Vent the heater vertically in a system in accordance with AS/NZS 5601.1 and 

local codes. Double-wall vent connector is recommended; however single-wall 

pipe is allowed in some circumstances. Consult your local code official for detailed 

information. 

Do not 

use a draft hood with this heater.

To connect a double wall metal gas vent to the heater, order the appropriate Metal 

Flue Collar from the chart below:

1.  See Table 4 to determine allowable vent sizes for your heater.

NOTICE:

 Table 4 is for installations in which the total lateral vent length (that is, the horizontal distance from 

Combustion

Chamber

Flue Collar

10.16 cm x 20.32 cm

(4" x 8") Metal Flue Collar

Vent Body

Clean the Interior Surface

Vent Pipe

Clean and RTV 

This Surface

Figure 18.

Read “VERTICAL VENTING” before using this table.

Table 4. 

– Permitted Minimum and Maximum Vent Heights By Size and Heater Model

Metal Flue Collar

Part No.

100 mm x 150 mm 

(4” x 6”)

SF 43-11-06

100 mm x 200 mm 

(4” x 8”)

SF 43-11-08

Double-Wall Vent with Double-Wall Connector in Meters (Feet)

Vent Size

Model 200

Height min./max.

Model 300

Height min./max.

Model 400

Height min./max.

150 mm (6 in.)

 1.8 m (6 ft.) / 22 m (72 ft.)

Not Suitable

Not Suitable

200 mm (8 in.)

1.8 m (6 ft.) / 22 m (72 ft.)

1.8 m (6 ft.) / 22 m (72 ft.)

2.4 m (8 ft.) / 22 m (72 ft.)

Содержание MasterTemp 200





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды