manualshive.com logo in svg

Pentair EASYTOUCH PL4, Руководство по установке

Пантэр EASYTOUCH PL4 - это интеллектуальный контроллер для бассейнов и спа-систем. Установочное руководство доступно для загрузки на manualshive.com, абсолютно бесплатно. Этот manual поможет вам правильно настроить и использовать вашу систему, чтобы получить максимальное удовольствие от отдыха на вашем участке.

Поделиться
Скачать
background image

                                                                                                                                                                                            

i

 

                                                                              

EASYTOUCH

® 

PL4/PSL4 Control Systems Power Center Installation Guide 

Contents

IMPORTANT WARNING AND SAFETY INSTRUCTIONS .......................................................................ii - v

General Installation Information ....................................................................................................................v

Section 1:  Power Center Overview .......................................................................................................... 1

Power Center Installation Overview ............................................................................................................. 3
      Power Center (without built-in Subpanel) ............................................................................................... 4
Preparing the Power Center Enclosure ........................................................................................................ 5
Mounting the Power Center .......................................................................................................................... 6
Installing Conductors to the Power Center ................................................................................................... 7
Connecting AC Power to the Power Center ................................................................................................. 7
Electrical Wiring and High Voltage Connections .......................................................................................... 8
Installing Conduit and Conductors to the Power Center .............................................................................. 9
Accessing the System Circuit Board and Electronics ................................................................................ 10
Connecting the System Relays .................................................................................................................. 11
Installing Valve Actuators ........................................................................................................................... 12
Installing and Connecting Temperature Sensors ........................................................................................ 13
    Water Temperature Sensor .................................................................................................................... 13
    Ambient Air Temperature Sensor (for freeze protection) ........................................................................ 13
    Solar Temperature Sensor (Optional) ..................................................................................................... 15
Connecting a Standard Gas Heater ........................................................................................................... 16
Connecting Pentair UltraTemp Heat Pump to System COM Port .............................................................. 17
Connecting an IntelliFlo Pump to System COM Port ................................................................................. 17
Connecting an IntelliChem Controller to System COM Port ...................................................................... 18
Connecting an IntelliChlor (SCG) to System COM Port  ............................................................................ 18
Wiring IntelliChlor (SCG) Transformer to Filter Pump Relay  ..................................................................... 19
Rewiring the System Transformer for 240 VAC .......................................................................................... 21

Accessories  ............................................................................................................................................. 22

Installing the Indoor Control Panel ............................................................................................................. 22
Wiring the Indoor Control Panel to the System COM Port ......................................................................... 23
Mounting and Cabling the Indoor Control Panel ........................................................................................ 24
Installing the Wireless Controller ................................................................................................................ 26
     Connecting the Wireless Controller Transceiver .................................................................................... 28

System Start-Up ....................................................................................................................................... 30

    Check Electronics .................................................................................................................................. 30
    System Test ............................................................................................................................................ 30
    Testing the auxiliary relays ..................................................................................................................... 30
EasyTouch PL4/PSL4 Control System Circuit Board Connections  ........................................................... 31
EasyTouch PL4/PSL4 Control System System Wiring Diagram ................................................................ 32
Solar System Installation ........................................................................................................................... 33
    Solar System Start-Up ........................................................................................................................... 33
Pool Cleaner Protection ............................................................................................................................. 33
Installing the EasyTouch PL4/PSL4 Control System Outdoor Control Panel ............................................. 33
EasyTouch PL4/PSL4Control System Outdoor Control Panel  .................................................................. 35
Plumbing Requirements ............................................................................................................................. 37
     Equipment Location .............................................................................................................................. 37

Glossary .................................................................................................................................................... 40

Содержание EASYTOUCH PL4

















































Отзывы:

Нет отзывов

Похожие инструкции для EASYTOUCH PL4

Wavetec Spectra Installation Manual preview
Spectra
Бренд: Wavetec Страницы: 17
Calsense ET1 Manual To Programming preview
ET1
Бренд: Calsense Страницы: 9
MaestroHome Smart Controller Quick Setup Manual preview
Smart Controller
Бренд: MaestroHome Страницы: 10
NEC UNIVERGE SL2100 Networking Manual preview
UNIVERGE SL2100
Бренд: NEC Страницы: 196
NEC UNIVERGE SL2100 Hardware Manual preview
UNIVERGE SL2100
Бренд: NEC Страницы: 174
NEC ElectraElite IPK General Description Manual preview
ElectraElite IPK
Бренд: NEC Страницы: 151
Panasonic KX-NS300 Cabling Configuration preview
KX-NS300
Бренд: Panasonic Страницы: 5
Panasonic KX-HTS Series Setup Reference Manual preview
KX-HTS Series
Бренд: Panasonic Страницы: 14
Panasonic HDVC-MPCS Specification preview
HDVC-MPCS
Бренд: Panasonic Страницы: 2
Bang & Olufsen Beolink 1000 Service Manual preview
Beolink 1000
Бренд: Bang & Olufsen Страницы: 9
Bang & Olufsen Beolink 1000 User Manual preview
Beolink 1000
Бренд: Bang & Olufsen Страницы: 12
Hach SC1500 User Manual preview
SC1500
Бренд: Hach Страницы: 86
ZEHUS Controller Rider'S Manual preview
Controller
Бренд: ZEHUS Страницы: 28
Valfonta S3 Operation And Installation Instructions Manual preview
S3
Бренд: Valfonta Страницы: 12
Daikin ALTHERMA User Manual preview
ALTHERMA
Бренд: Daikin Страницы: 5
Harman Kardon OMNI 10 Quick Start Manual preview
OMNI 10
Бренд: Harman Kardon Страницы: 25
Uniss SR601 Operation Instructions Manual preview
SR601
Бренд: Uniss Страницы: 21
IDK SWC-2000 User Manual preview
SWC-2000
Бренд: IDK Страницы: 96

Бренды по названию

Популярные бренды

Загрузить еще бренды