Pentair EASYTOUCH PL4 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 48

background image

EASYTOUCH

®

PL4/PSL4 Control Systems Installation Guide

EASYTOUCH

®

PL4/PSL4 Control Systems Installation Guide

17

Connecting a Pentair UltraTemp

®

Heat Pump to the System COM Port

Be sure to check the UltraTemp Heat Pump terminal block conductor colors and pinouts (located on
the back of the Auto Set board) before connecting it to the EasyTouch

®

PL4/PSL4 Control Systems

COM port. The See the wiring table below for the pin configuration.

IMPORTANT: On the UltraTemp heat pump AutoSet circuit board ONLY CONNECT PIN 3 (YELLOW)
and PIN 2 (GREEN) to the EasyTouch PL4/PSL4 Control Systems COM port pins YELLOW and GREEN
respectively. Do not connect pin 1 or pin 4 on the AutoSet board or the COM port. These pins are not

COM Port Wire Color

Descripion

UltraTemp Heat Pump Pin Number and Wire Color

PIN 4 (RED)

(DO NOT USE)

+15 VDC

PIN 4 (DO NOT USE)

PIN 3 (YELLOW)

+ DATA

PIN 3 (YELLOW)

PIN 2 (GREEN)

- DATA

PIN 2 (GREEN)

PIN 1 (BLACK)

(DO NOT USE)

GROUND

PIN 1 (DO NOT USE)

Connecting an IntelliFlo

®

Pump to the System COM Port

(see Illustration on page 20)

The RS-232 communication cable (provide with IntellliFlo pump) consists of a 50 ft 22 AWG four
conductor low voltage cable. The EasyTouch PL4/PSL4 Control Systems filter pump output is
rated at 120 VAC, 15 AMP maximum. Check the electrical rating marked on the pump motor before
connecting it to the system.

To connect the IntelliFlo pump communication cable to the Power Center:

1.

Switch OFF power Power Center at the main house circuit breakers.

2. Run the communication cable from the pump to the enclosure.
3. Insert the cable conductors into the one of the plastic grommet fittings, located on the

lower left side of the enclosure and pull the cable up through the low voltage to the PL4/
EasyTouch PL4/PSL4 Control Systems circuit board. See illustration on page 19.

4. Strip back the outer jacket four (4) inches. Strip back each conductor a ¼-inch.
5. Insert the conductors into the COM Port

(J20)

screw terminals located on the top of the

EasyTouch PL4/PSL4 Control Systems circuit board (see illustration below and page 31).
Secure the conductors with the screws. For wiring details, refer to the pin configuration
shown below. Note: Multiple conductors may be inserted into a single screw terminal.

IntelliFlo Pump
COM Port

COM PORT - J20 connector:

For IntelliFlo

®

Pump, iS4 Spa Side Remote QuickTouch

®

,

PL4/PSl4 Control System Indoor Control
Panel and Pl4/PSL4 Control System
Wireless Controller Transceiver.

J20

EasyTouch
PL4/PSL4
Control
Systems
COM PORT

Pin configuration

EasyTouch PL4/PSL4 Control Systems
COM PORT (J20)
Screw Terminal

COM Port

screw

terminal

connector

IntelliFlo

®

Pump

(2-wire

cable)

2 (GRN)

GREEN (Pin

6)

3 (YEL)

YELLOW

(Pin 7)

«
...
23
24
25
26
27
...
»

Содержание EASYTOUCH PL4

















































Отзывы:

Нет отзывов

Похожие инструкции для EASYTOUCH PL4

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: UNITED Страницы: 22

Бренд: Bartlett Страницы: 5

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 111

Бренд: C&C Страницы: 17

Бренд: WAGNER Страницы: 60

Бренд: Vizio Страницы: 65

Бренд: iluminize Страницы: 2

Liberty Vertical Picket

Бренд: National ramp Страницы: 9

Бренд: DSE Страницы: 2

FieldPoint FP-AI-100

Бренд: National Instruments Страницы: 17

Бренд: Trane Страницы: 72

ZITON RADIO LOOP MODULE

Бренд: EMS Страницы: 26

Бренд: Danfoss Страницы: 30

Бренд: Mitsubishi Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды