Pentair EASYTOUCH PL4 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 48

background image

EASYTOUCH

®

PL4/PSL4 Control Systems Installation Guide

EASYTOUCH

®

PL4/PSL4 Control Systems Installation Guide

19

IMPORTANT! IntelliChlor (SCG) AC transformer wiring Instructions: When using the EasyTouch
PL4/PSL4 Control Systems with the IntelliChlor (SCG) option , be sure the IntelliChlor (SCG) AC
transformer conductors are connected to the LOAD SIDE OF THE MAIN FILTER PUMP RELAY located
in the enclosure (see page 20). This ensures that the IntelliChlor cell produces chlorine only when the
main filter pump is on. This method does not require a ground fault circuit-interrupter (GFCI) for the
IntelliChlor power center.

TO AVOID AN ELECTRICAL HAZARD AND EQUIPMENT DAMAGE TO THE ENCLOSURE
AND INTELLICHLOR CELL: FIRST DISCONNECT AC POWER TO THE ENCLOSURE
BEFORE CONNECTING THE INTELLICHLOR COMMUNICATION CABLE.

Connect the IntelliChlor (SCG) transformer conductors to the main filter pump relay as follows:

1.

Switch OFF AC power

to the Power center at the house panel circuit breaker.

2. Loosen the two retaining screws securing HIGH VOLTAGE FRONT COVER PANEL.

Remove the panel from the enclosure (see illustration below).

3.

Locate the FILTER PUMP RELAY. Connect the IntelliChlor SCG transformer

conductors to the LOAD SIDE of the relay. See relay wiring diagram shown on page
20.

4. After electrical connections have be completed, install the HIGH VOLTAGE FRONT COVER

PANEL and tighten the two retaining screws to secure in place.

5.

Switch AC power ON

to the Power Center.

BEFORE REMOVING THE HIGH VOLTAGE COVER PANEL FROM THE POWER
CENTER,

switch OFF the main power at the house circuit breaker box.

Wiring IntelliChlor (SCG) Transformer to Filter Pump Relay

EasyTouch

®

PL4/PSL4 Control Systems Power Center (front view)

High Voltage
Cover Panel Tabs

Retaining screws
(for High Voltage Cover Panel)

Front door

Slots for High Voltage
Cover Panel

Retaining screws
(for Outdoor Control Panel

Retaining

screws

(for Outdoor

Control Panel

Flip down the Outdoor Control Panel to access circuit
boards in low voltage compartment

Low voltage

raceway

Filter Pump

Relay

«
...
25
26
27
28
29
...
»

Содержание EASYTOUCH PL4

















































Отзывы:

Нет отзывов

Похожие инструкции для EASYTOUCH PL4

Бренд: 2N Страницы: 4

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: Salda Страницы: 20

Бренд: K&K Страницы: 6

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

CEmarking RCX221

Бренд: Yamaha Страницы: 468

GECO LUX GECO60

Бренд: GiBiDi Страницы: 48

Бренд: Sabiana Страницы: 60

Бренд: KIPI Страницы: 44

Бренд: Gallagher Страницы: 2

Бренд: Intermatic Страницы: 3

Бренд: Woodward Страницы: 32

Бренд: Midland Страницы: 37

Бренд: Hanma Страницы: 3

NETBuilder II DPE 80

Бренд: 3Com Страницы: 32

Бренд: 4IPNET Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды