Pentair BK4875 Скачать руководство пользователя страница 1

Description

Corrosion resistant shallow well ejector package (Model BK4875) 

includes a plastic shallow well ejector, necessary mounting 

hardware, and an assortment of venturis and nozzles to suit your 

pump model. For use with Berkeley Pump Models 3PL, 5PL, 7PL, 

10PL, 10PLS11C and 15PLS11C (See Page 7 for Performance).

General safety information

Follow safety instructions in your pump owner's manual.
Be sUre pump is turned off and all pressure is re leased 

before installing shallow well ejector.

california proposition 65 Warning

 This product and related accessories contain 

chemicals known to the State of California to cause cancer, 

birth defects or other reproductive harm.

DisassemBly

Refer to Figure 5 for part description and part list.
1.  Remove the 4 screws that fasten the insert assembly into 

ejector body (See Figure 1).

2.  Unscrew the venturi from the ejector body insert (See Figure 

2).

3.  Use 5/8” deepwell socket to gently unscrew nozzle from ejector 

body insert (See Figure 2).

4.  Select the correct nozzle and venturi from Table I.
5.  Reassemble as follows.

assemBly

1.  Select nozzle and venturi according to Table I.
2.  Thread nozzle into ejector body insert (See Figure 2). Use 5/8” 

socket to seat nozzle. 

Do not overtighten.

3.   Install small O-Ring in groove on venturi (See Figure 2). Thread 

venturi into ejector body insert (See Figure 1) hand tight. 

4.  Install O-ring in groove on end of ejector body (See Figure 1). 

Thread check valve onto ejector body (See Figure 1) hand 

tight. Be sure O-Ring is seated in groove. 

5.  Install gasket on step in ejector body; install ejector body insert 

in ejector body (be sure it seats) with D-shaped opening DOWN 

(toward AVC plug) and venturi UP (See Figure 1).

6.  Use four screws to mount insert assembly in ejector body 

(See Figure 1). Be sure insert assembly is seated and all four 

screws are well started before tightening any screw. 

Do not 

overtighten.

note: When insert assembly is correctly installed and ejector body 

is right side up, AVC port will be on bottom of ejector body and 

molded-in part number on insert (N40-39P) will be at 9:00 o’clock 

position as you look into ejector body.

installation

 

1.  Loosen stainless steel clamp (Figure 5, Ref. No. 2) until it fits 

over ejector body flange.

2.  Place O-ring in circular groove on face of pump flange (See 

Figure 3).

figure 1

2556 0796

figure 2

2557 0796

 

pump 

nozzle Venturi

 

model 

number number

 3PL 

#51 

N32P-72

 5PL 

#51 

N32P-63

  7PL, 10PLS11C 

#54 

N32P-64

  10PL, 15PLS11C 

#51 

N32P-65

taBle i: VentUri / nozzle sizinG

figure 3

1199 0794 NF

293 WRIGHT STREET, DELAVAN, WI 53115  WWW.BERKELEYPUMPS.COM
PH: 888-782-7483

InstallatIon, operatIon & parts Manual

Model BK4875  

Premium Shallow Well 

 Ejector Package

© 2013 Pentair, Ltd. All Rights Reserved. 

BE549 (Rev. 02/25/13)

Содержание BK4875









Отзывы: