background image

P/N  619339

2

REV. G   4-23-1

2

SECTION I.

IMPORTANT SAFETY INSTRUCTIONS

When installing and using this electrical equipment, basic safety precautions should always be followed,
including the following.

1.

This light can be installed on storable above ground or permanent above ground pools.

2.

To reduce the risk of electric shock, if any cord becomes damaged, return the entire transformer

assembly for repair or replacement.

3.

Risk of entrapment, injury or death. Use plumbing passageways only to return water to pool. Do not use

as a suction device.

4.

Risk of electrical shock. Connect only to a grounding type circuit protected by a ground fault circuit

interrupter. Contact a licensed electrician if you cannot verify that the receptacle or circuit is protected
by a ground fault circuit interrupter. Do not use an extension cord.

5.

Locate your pool so that the wall is at least 3.0 meters from all electrical receptacles and at least 6.1

meters from all receptacles not protected by a ground fault circuit interrupter. It is also very important
to locate the pool so that it is not under any electrical wiring, that is less than 5.5 meters vertically
above the pool wall and within an area located 3.0 meters outside the pool walls. The pool must also
never be located under any lighting fixture or within 1.7 meters measured horizontally from any fixture
mounted less than 1.7 meters vertically above the pool water level.

6.

Risk of injury. Install the top of the lens with a minimum of 20.3 centimeters and a maximum of 25.4

centimeters below top of pool wall or in manufacturers pre-punched return fitting hole.

7.

Do not use electrical equipment within 3.0 meters of pool wall unless specifically C.E. listed for that use.

SECTION II.

LAMP HOUSING INSTALLATION

1.

Remove the bulb retainer nut and push the bulb assembly out from the rear

of the fitting body so that it will come out of the front of the fitting. The
flow director will come off along with the bulb assembly; see Figure 1.
Push the red cap/plug in the end of the bulb assembly. It will be removed
later.

2.

Unscrew the threaded wall flange from the fitting body by rotating it

counter-clockwise.

NOTE

Retain the gaskets supplied and keep them accessible.

3.

Use the thread seal tape provided. Snugly wrap the threaded wall

flange in a clockwise direction (as viewed from the back) starting at the
edge of the threads; see Figure 2. Work towards the flange lip
(overlapping 1/2 of the tape width with each wrap) then back towards
the starting point.
• If you have a new pool, move on to step 10.
• If the water level is below the return fitting on an existing pool,

remove the old fitting and move on to step 10.

• If the pool is full of water, follow steps 5 through 9.

Figure 2.

Start at the
edge

Always wrap thread seal
tape clockwise

Figure 1.

P

U

S

H

Bulb Retainer Nut

Содержание AquaLuminator











Отзывы: