2
3
WS SportTac, WS5, WS Workstyle
This product has been tested and approved against the personal protection
equipment (PPE) directive 89/686/EEC, and is also in compliance with the
electromagnetic compatibility (EMC) directive 2004/108/EC for CE marking.
NOTE: Read these instructions carefully before use and save for future
reference.
1. WHAT IS WHAT
(A:1). Headband wire (stainless steel)
(A:2) Two-point fastener (headband wire)
(A:3) Ear cushion (PVC foil and Polyester foam)
(A:4) Microphone for surround sound
(A:5) Attenuation cushion (Polyester foam)
(A:6) Inner shell
(A:7) Outer shell
(A:8) Clamp
(A:9) Headband (sheet metal)
A:10). Headband padding (Thermoplastic Elastomer or Leather)
(A:11) AUX audio input, 3.5 mm stereo
(A:12) Audio input, J22
(A:13) On/Off/Mode
(A:14) VOL+, VOL –
(A:15) Speech microphone
(A:16) Bluetooth button
(A:17) Charger jack
(A:18) Charger
(A:19) Rechargeable AAA NiMH batteries
(A:20) Stereo cable 3,5mm. FL6CE
2. FITTING AND ADJUSTMENT
(B:1)
Open the headband.
(B:2)
Slide out the shells. Tilt the upper part of the shell outwards to ensure the
wires are positioned away from the headband.
(B:3)
Adjust the height of the shells by sliding them up or down whilst holding
the headband in place.
(B:4)
The headband should be positioned across the top of the head.
(B:5)
Before folding the hearing protector, press the shells together. Leave
about 4 mm of the headband wire visible.
(B:6)
Fold the headband as shown. Ensure that the ear cushions are not
creased and that they lie flat against each other. Note: Be sure to remove the
cord from the audio input
(A:11)
before folding the headband.
3. USAGE/FUNCTIONS
3:1 Inserting the batteries
Remove the left outer shell.
(C:1)
Insert a blunt tool or finger under the edge of the clamp and pull outwards
3–4 mm.
(C:2)
Press/slide the clamp down. Remove the shell.
Insert the rechargeable AAA NiMH batteries included with the product. Ensure
that the poles are correctly aligned.
The headset can also operate on alkaline batteries.
Warning!
Do NOT charge alkaline batteries as this may damage the headset.
Replace the outer shell:
(C:3)
Ensure that the clamp is fully pressed down.
Position the shell from the top down, ensuring that the hook on the top of the
shell
(C:4)
fits in the hole on the inner shell
(C:5)
.
(C:6)
Press/slide the clamp up once the shell is in place.
3:2 Charging your headset
Connect the charger to the charger jack on the headset
(A:17)
.
Charge the headset for 8 hours to achieve the maximum battery capacity.
Содержание WS SportTac
Страница 1: ...WS SportTac WS5 WS Workstyle ...
Страница 2: ...A A 1 A 2 A 3 A 4 A 5 A 6 A 7 A 8 A 9 A 10 A 11 A 12 A 14 A 13 A 15 A 17 A 18 A 19 A 16 A 20 ...
Страница 4: ...F H H 1 H 2 H 3 I J Max AUX input signal level 1 5 Vrms AUX input signal level 20 mVrms 82dB ...
Страница 198: ...3M Svenska AB Box 2341 SE 331 02 Värnamo Sweden t 46 0 370 65 65 65 f 46 0 370 65 65 99 e info peltor se FP3657 Rev a ...