Pella INSYNCTIVE DESIGNER Series Скачать руководство пользователя страница 5

Страница: 5 / 15

PELLA

DESIGNER SERIES

BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE

TECHNOLOGY

DETAILED INSTRUCTIONS

See

InsynctiveSupport.Pella.com

for how-to videos.

SETTING UP PELLA

DESIGNER SERIES

BETWEEN-THE-GLASS

BLINDS OR SHADES

1. Get Started

• To unpack BLIND or SHADE, open the Hinged Glass Panel

(HGP) and remove the cardboard corner protectors and bands

that secure BLIND or SHADE.

• Check to make sure that the wire is firmly seated into the

groove by the HGP gasket. Press any loose portions of the

clip back into the groove in the HGP.

• Close the HGP and ensure that it is securely latched.

• REMOTE ships in a separate package. Unpack REMOTE.

To set up REMOTE, follow Remote Quick Start Guide or

Remote Product Guide, or visit InsynctiveSupport.Pella.com

for more information.

2. Set up BLIND or SHADE

Complete the following steps to set up BLIND or SHADE.

• Locate the wire that runs from the BLIND or SHADE cover

to the battery at the bottom of the unit. For casement

windows, sliding patio doors and hinged patio doors, the

wire will be located on the same side as the HGP latch

releases. For double-hung or Precision Fit

window units,

the wire will be located on the right-hand side of the unit.

• With the HGP closed, touch the top end of REMOTE to

BLIND or SHADE cover approximately 6" from the edge of

the glass on the side where the wire is connected. Move

REMOTE back and forth slowly until BLIND or SHADE

completes a quick up/down motion to indicate BLIND or

SHADE has entered sync mode.

• Press and hold Up button on REMOTE until BLIND or

SHADE completes a quick up/down motion. This will

require the Up button to be pressed for about 3 seconds.

CAUTION:

DO NOT remove or cut the white cord that limits

the opening of the HGP. Doing so may cause serious damage,
including glass breakage, to your Pella product. The cord should
only be detached by a qualified technician when performing
service-related procedures.

HINGED

GLASS

PANEL

(HGP)

BUTTON

DOWN

BUTTON

LED

LIGHT

CENTER

BUTTON

SOLAR

PANEL

WIRE

BLIND OR

SHADE

COVER

HGP

LATCH

RELEASE

COVER

REMOTE

MEASURE 6"

FROM END WHERE

WIRE CONNECTS

BATTERY

VIEW WITH HGP OPEN

VIEW WITH HGP CLOSED

CORD

Содержание INSYNCTIVE DESIGNER Series
















Результаты поиска

Содержание INSYNCTIVE DESIGNER Series

Отзывы:

Бренды по названию

Популярные бренды

Pella INSYNCTIVE DESIGNER Series, Руководство по эксплуатации продукта

Результаты поиска

Содержание INSYNCTIVE DESIGNER Series

Отзывы:

Бренды по названию

Популярные бренды