PELICAN
TM
StealthLite
TM
2400
BATTERY INSTALLATION
1.
Remove lens housing by turning counter-
clockwise.
2.
Remove the lamp and contact module.
3.
Remove used batteries and replace with fresh
batteries as shown on the outside of the
engraved body.
4.
Replace the contact module and lamp.
5.
Replace lens housing squarely on threads and
turn clockwise while pressing on the lens hous-
ing slightly.
ON/OFF
Swing the switch lever to the right (light facing away
from you) until light activates. To turn light off, swing
the switch lever to the left (light facing away from
you) until light goes off.
WARNING –
Explosion Hazard - Batteries must
only be changed in non-hazardous locations
WARNING –
Explosion Hazard - Substitution of components
may impair suitability for use in hazardous locations
CAUTION:
If light is not to be used for some time, remove
batteries to prevent possible leakage and corrosion.
LAMP REPLACEMENT
1.
Remove lens housing by turning counter-clockwise.
2.
Remove the lamp and contact module.
3.
Replace the contact module and lamp.
4.
Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing
slightly.
PRODUCT SPECIFICATIONS
Lamp Type:
Xenon
Battery Type:
4 AA Cell Alkaline (Included)
Battery Brand:
Eveready
®
Energizer
®
REPLACEMENT PARTS
CAT #
DESCRIPTION
2401
O-RING
2404
LAMP MODULE
CAUTION: Read This Notice Before Use.
Hydrogen Gas Absorber Pellets
Located inside the flashlight are catalyst pellets which
are present to absorb hydrogen gas that could possibly
be emitted by defective, leaking, reversed polarity or
heavily discharged batteries. If the pellets become wet,
let them air dry. Pelican Products assumes no liability
for any brand batteries which are defective or cause
injury to anyone when used in any Pelican flashlight.
WARNING!
STATIC HAzARD - clean only with a
damp cloth
StealthLite
TM
2400
Cat. #2400
INSTRUCCIONES DE FUNCIONAMIENTO
INSTALACION DE LAS PILAS
1.
Retire el bastidor de la lente girándolo en
sentido contrario de las agujas del reloj.
2.
Retire el módulo de la bombilla y el contacto.
3.
Saque las pilas gastadas y sustitúyalas por pilas
nuevas tal y como se indica en la parte exterior del
cuerpo de la linterna.
4.
Vuelva a colocar el módulo de la bombilla y el
contacto.
5.
Vuelva a colocar el bastidor de la lente sobre la
rosca y gire en el sentido de las agujas del reloj al
mismo tiempo que ejerce un poco de presión sobre
el mismo.
ENCENDIDO / APAGADO
Para encender la linterna (con el extremo de la bombilla
apuntando en la dirección opuesta a usted), gire la
palanca del interruptor hacia la derecha hasta que se
encienda. Para apagarla, gire la palanca del interrup-
tor hacia la izquierda (con el extremo de la bombilla
apuntando en la dirección opuesta a usted), hasta que
se apague.
Advertencia -
Peligro de explosión - La sustitución
de componentes puede afectar a la idoneidad de su
uso en zonas potencialmente explosivas.
Advertencia -
Peligro de explosión - Las baterías
sólo deben sustituirse o cargarse en zonas no peli-
grosas.
PRECAUCION:
Si no se va a usar la linterna por algún tiempo, retire
las pilas para evitar la posibilidad que ocurra una
fuga y corrosión.
REEMPLAZO DE LA BOMBILLA
1.
Retire el bastidor de la lente girándolo en
sentido contrario de las agujas del reloj.
2.
Retire el módulo de la bombilla y el contacto.
3.
Vuelva a colocar el módulo de la bombilla y el
contacto.
4.
Vuelva a colocar el bastidor de la lente sobre la
rosca y gire en el sentido de las agujas del reloj
al mismo tiempo que ejerce un poco de presión
sobre el mismo.
ESPECIFICACIONES DEL PRODUCTO
Tipo de bombilla:
Xenón
Tipo de pila:
4 AA Cell Alkaline (Included)
Marca de las pilas: Energizer
®
de Eveready
®
PIEZAS DE REPUESTO
NO. DE CAT.
DESCRIPCION
2401
Junta tórica
2404 Módulo de la bombilla
23215 Early Ave. • Torrance, CA 90505 USA
Tel (310) 326-4700 • FAX (310) 326-3311
www.pelican.com
PELICAN
TM
CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel (780) 481-6076 • FAX (780) 481-9586
PELI
TM
PRODUCTS, S.L.U.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel (+34) 93.467.4999 • FAX (+34) 93.487.7393
www.peli.com
© PELICAN PRODUCTS 2010 2403-311-001 5-0697 Rev A AU/10
All trademarks and logos displayed herein are registered and unregistered
trademarks of Pelican Products, Inc. and others.
Eveready and Energizer are registered trademarks of Eveready Battery Company, Inc.
23215 Early Ave. • Torrance, CA 90505 USA
Tel (310) 326-4700 • FAX (310) 326-3311
www.pelican.com
PELICAN
TM
CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel (780) 481-6076 • FAX (780) 481-9586
PELI
TM
PRODUCTS, S.L.U.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel (+34) 93.467.4999 • FAX (+34) 93.487.739 • www.peli.com
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify
you of any handling and return postage charges.
If your local retailer does not stock the above acces-
sory parts, you may order them directly from Pelican
Products. Send check or money order in U.S. dol-
lars, or order by phone using MasterCard or VISA
(ask for Customer Service). SORRY, NO C.O.D.’s.
Subject to sales tax. Allow 2-3 weeks delivery time.
Pelican Products pays postage and handling charg-
es. POSTAGE PAID FOR U.S. zIP CODES ONLY.
Cat. #2400
PELICAN LEGENDARY LIFETIME
GUARANTEE OF EXCELLENCE
Pelican Products, Inc. guarantees its products for a
lifetime against breakage or defects in workmanship.
This guarantee does not cover the lamp or batteries
(rechargeable or alkaline). Any liability, either expressed
or implied, is limited to replacement of the product.
This guarantee is void if the Pelican product has been
abused beyond normal and sensible use.
This guarantee does not cover shark bite, bear attack or
damage caused by children under five.
Lifetime Guarantee does not cover Roto Molded or
AALG products. Refer to www.pelican.com/warranty
for full details.
SUBMERSIBLE
Battery Replacement
Do not mix battery brands or use Nicad or zinc
Carbon Batteries. Do not mix old and new batteries.
Replace all batteries at the same time.
Lamp Replacement
Lamp replacement may only be performed
in a non-hazardous area.
DO NOT MODIFY THIS PRODUCT!
