background image

3.Avoid skin contact.  Immediately wash contacted areas 

completely with water and soap.

4.

Never swallow machine oil.

5.Keep machine oil out of the reach of children.

If swallowed, do not induce vomiting.

Immediately go to see a doctor.

6.Dispose of the waste oil and/or containers properly as demanded

by law.  If you have further questions on its disposal, consult the

store or shop at which you purchased it.

7.After opening the oil container, be sure to seal it to prevent dust

and water from getting into the oil and keep it in the dark to avoid

direct sunlight.

W

W

ARNING

ARNING

Before starting the machine

Machine table

1.Before turning the power on, visually check the cables and 

connectors for defective conditions, such as damage, 

disconnection and/or loosening. 

2.Never bring your hands close 

to the needle and/or pulley 

when turning on the power.

3. When the machine is use for 

the first time, check to make 

sure the machine pulley 

rotates counterclockwise as 

seen from the pulley 

(operating direction).

4.Well trained operators should use the machine after studying

these precautions and the instruction manual carefully.

5.Regarding symbols that indicate a danger or a warning, read and

study "2. Waning indications" carefully and give training on safety

to the operators as required.

6.Run the machine at the speed less than 3/4 of its maximum for 

the first one month.

W

W

ARNING

ARNING

Precautions while you are running the machine

1.

Do not run the machine with the safety devices removed,

such as eye guard, finger guard, pulley cover, etc.

2.

Never bring your hands under the needle while running the

machine.

3.A clutch motor keeps on running for a while after the power is

turned off.  Therefore, be careful even after the power is turned

off as the machine could start running by pressing the machine

treadle.

4.

To prevent accidents, never bring any part of your fingers, 

hair and clothes near the machine pulley, V belt, motor pulley,

thread take-up and needle bar.  Also never leave scissors, 

tweezers, tools, etc. around these areas.

5.Always turn off the power while the machine is not used or before

leaving the machine table.

6.In the event of a power failure, be sure to turn off the power.

7.While operating the machine, wear clothes that cannot be caught

in the machine.

8.

Do not put any tools or other unnecessary objects on the 

machine table while running the machine. 

CA

CA

UTION

UTION

Maintenance, Check, Repair

1.Well trained people should perform maintenance, check and

repair of the machine after studying these precautions and the

instruction manual carefully.

2.

If it is necessary to lay the machine backward for 

maintenance, check and repair, always turn off the power, unplug

the machine and press the treadle to make sure that the machine

dose not operate before beginning any of the procedures.

3.

Before installing/removing the V belt, always turn off the 

power, unplug the machine and press the treadle to make sure

the machine does not operate.

4.Carry out daily maintenance work and periodical inspections

properly by following these precautions and the instruction 

manual.

5.Employ Pegasus' genuine parts when repairing the machine

and/or replacing the parts.  We are not responsible for accidents

caused by any improper repair/adjustment and substituting other

parts for thoes manufactured by Pegasus.

6.Do not attempt to modify the machine at your own discretion.

We are not responsible for accidents caused by the modification.

7.Be sure to replace the safety devices and/or safety covers that

are temporarily removed for maintenance and/or adjustment.

8.After performing maintenance, check and repair, make sure that

turning on the power does not pose any danger to you.

6

From the library of: Superior Sewing Machine & Supply LLC

Содержание FS700 Series





































Отзывы: