Peg-Perego Viaggio0+1, Инструкция по эксплуатации

Страница: 27 / 124

27
• Ensure that the vehicle’s three-point seatbelt fixing the car
seat is always taut and not twisted. It should be replaced
in the case of heavy stress as a result of an accident.
• Never leave your child unattended in the car seat:
watch him/her even when s/he is sleeping.
• Never remove the child from the car seat when the
vehicle is in motion.
• Make sure that the car seat is not blocked by a mobile
part of the vehicle seat or by a door.
• Adjust the height and tension of the shoulder straps,
ensuring that they are as snug to the child’s body as possible
without constricting him/her too much. Check that the
harness is not twisted and that the child does not release it.
• This car seat is not intended for prolonged periods of
sleeping.
• Do not leave the car seat in the vehicle when exposed
to the sun. Some parts might heat up and be harmful
to the delicate skin of your child. Check the seat is not
too hot before seating your child.
• Do not use the car seat without its fabric cover; this
must not be replaced with one not approved by the
manufacturer since it is an integral part of the car seat
and the safety system.
• If in doubt, contact the manufacturer or retailer of the
car seat.
• Do not remove the adhesive and stitched labels since
this might make the product not compliant with legal
requirements.
• Do not use the car seat if it has signs of breakage or missing
parts, if it is second-hand or if it has been subjected to
heavy impacts in an accident, because it might have
suffered extremely dangerous structural damage.
• Do not alter the product.
• For any repairs, replacement parts and information
about the product, contact the after-sales assistance
service. Contact information is provided on the last
page of this manual.
• The car seat must always be secured in the vehicle,
even when the child is not sitting in it; in the event of
sudden braking, it could injure the passengers.
• Do not use this car seat if more than seven years have
elapsed from the date of production indicated on the
structure; the natural aging of the materials may mean the
car seat is no longer compliant with safety standards.
• Do not use accessories that have not been approved by
the manufacturer or by the competent authorities.
Instructions for use
UNIVERSAL CATEGORY - Belted
Group 0+
Fastening with seatbelts
1•
IMPORTANT: For the correct use of the
“Viaggio 0+1 Switchable” car seat in Group 0+
mode, it is necessary to:
- Extract from under the seat the casing that enables
the car seat to be reclined.
To extract it, press the handle and pull it towards
you, extracting the base (arrows A and B).
- Use the lever (arrow C) to recline the seat to its
highest position.
2• “Viaggio 0+1 Switchable” car seat correctly installed to
be used as a Group 0+ car seat.
3• Install the “Viaggio 0+1 Switchable” car seat on the
vehicle’s seat so that it is rear-facing, as shown in the figure.
Pass the vehicle seatbelt between the frame and body
of the car seat following these steps:
- slip the belt into the light blue belt guides first (arrow A);
- fasten the belt, ensuring that it clicks into place (arrow B);
4• Pass the seatbelt through the upper light blue belt slot
(arrow C).
IMPORTANT: Take hold of the seatbelt and pull
it firmly, so as to ensure that the “Viaggio 0+1
Switchable” fits as close as possible to the vehicle
seat (arrow D).
Instructions for use
UNIVERSAL CATEGORY - Belted
Group 1
Fastening with seatbelts
5•
IMPORTANT: For the correct use of the “Viaggio 0+1
Switchable” car seat in
Group 1
mode, it is necessary to:
- Reposition the casing within the base of the car seat.
Press the lever and push inwards, as indicated in
the figure.
6• Install the “Viaggio 0+1 Switchable” car seat on the vehicle’s
seat so that it is front-facing, as shown in the figure.
7• To make it easier to pass the vehicle’s seatbelts
through the back of the car seat, it is necessary to
recline the car seat to its lowest position by operating
the lever, as shown in the figure.
8• Pass the vehicle seatbelt between the frame and body
of the car seat.
9• The waist strap must pass through the lower guides,
marked in red; fasten the belt, ensuring that it clicks
into place.
10• Tighten the waist strap, ensuring it has passed through
the lower guides, marked in red.
11• Bring the car seat back into the upright position by
pulling the handle below the seat (Fig. A) and pushing
the car seat as shown in the figure (Fig. B).
12• To complete the installation process, use the Steady
Fix device: open the clip and pass the diagonal strap
through it, ensuring that it is taut and not twisted (Fig.
A). Close the safety tab (Fig. B).
13•
IMPORTANT: Take hold of the seatbelt and pull
it firmly upwards, so as to ensure that the “Viaggio
0+1 Switchable” fits as close as possible to the
vehicle seat (Fig. C).
Once installed, the car seat may be reclined to the
desired position (See Point 6).
How to secure your child in the
“Viaggio 0+1 Switchable” car seat
14• Before placing the child in the car seat, release the
harness by pushing the red button on the crotch strap
buckle.
15• Lift the harness and attach the buckles to the elastic
bands on the sides.
16• Place the child in the car seat and arrange the harness over
the child’s shoulders and waist, as shown in the figure.