Peek Traffic LPM-14-E Скачать руководство пользователя страница 36

Страница: 36 / 42

4-7

S39 - Flow Control Bit Mapped Options Status

Default:

3 (00000011b)

Bits 0-2

Status of command options

0 =

No flow control

3 =

RTS/CTS (&K3) (Default.)

4 =

XON/XOFF (&K4)

5 =

Transparent XON (&K5)

6 =

Both methods (&K6)

Bits 3-7

Reserved

S40 - General Bit Mapped Options Status
Indicates the status of command options. Default to 105 (69h) (01101001b) .

Bit 0 - 1

MNP Extended Services (-Kn)

0 =

Disable extended services (-K0)

1 =

Enable extended services (-K1) (Default for MNP 10 models.)

2 =

Enable extended services (-K2)

Bit 2

Power Level Adjustment for Cellular Use ()Mn) (see S201 bit 6)

0 =

Disable power level adjustment ()M0) (Default.)

1 =

Enable power level adjustment ()M1 or )M2)

Bits 3-5

Break Handling (\Kn). 0=\K0, 1=\K1, 2=\K2, 3=\K3, 4=\K4, 5=\K5 (Default).

Bits 6-7

MNP block size (\An). 0=64, 1=128 (Default), 2=192, 3=256 chars.

S41 - General Bit Mapped Options Status
Indicates the status of command options. Default to 131 (10000011b).

Bits 0 -1

Compression selection (%Cn)

0 =

Disabled (%C0)

1 =

MNP 5 (%C1)

2 =

V.42 bis (%C2)

3 =

MNP 5 and V.42 bis (%C3) (Default.)

Bit 2, 6

Auto retrain and fallback/fall forward (%En)

Bit 6

Bit 2

0 =

Retrain and fallback/fall forward disabled (%E0) (Default.)

1 =

Retrain enabled (%E1)

0 =

Fallback/fall forward enabled (%E2)

Bit 3

Modem-to-modem flow control. 0=\G0 (Default), 1=\G1.

Bit 7

Enable fallback to V.22 bis/V.22 (-Qn). 0=Disabled (-Q0), 1=Enabled (-Q1) (Default).

S46 - Data Compression Control

Controls selection of compression. The following actions are executed for the given values:

Range:

136 or 138

Default:

138

S46=136

Execute error correction protocol with no compression.

S46=138

Execute error correction protocol with compression. (Default.)

S48 - V.42 Negotiation Action

The V.42 negotiation process determines the capabilities of the remote modem. However, when the capabilities of the remote modem are
known and negotiation is unnecessary, this process can be bypassed if so desired.

Range:

0, 7, or 128 If an invalid number is entered, it is accepted into the S-Register, but S48 will act as if 128 has been

entered.

Default:

S48=0

Disable negotiation; bypass the detection and negotiation phases; and proceed with LAPM.

S48=7

Enable negotiation. (Default.)

S48=128

Disable negotiation; bypass the detection and negotiation phases; and proceed at once with the fallback

action specified in S36. Can be used to force MNP.

Содержание LPM-14-E











































Результаты поиска

Содержание LPM-14-E

Отзывы:

Бренды по названию

Популярные бренды

Peek Traffic LPM-14-E, Справочное руководство

Результаты поиска

Содержание LPM-14-E

Отзывы:

Бренды по названию

Популярные бренды