Peek Traffic LPM-14-E Скачать руководство пользователя страница 10

Страница: 10 / 42

&T0

Terminate any test in progress.

&T1

Initiate local analog loopback.

&T2

Returns ERROR result code.

&T3

Initiate local digital loopback.

&T4

Allow remote digital loopback.

&T5

Disallow remote digital loopback request.

&T6

Request an RDL without self-test.

&T7

Request an RDL with self-test.

&T8

Initiate local analog loop with self-test.

Display current configurations.

&W0

Store the active profile in NVRAM profile 0.

&W1

Store the active profile in NVRAM profile 1.

&X0

Select internal timing for the transmit clock.

&X1

Select external timing for the transmit clock.

&X2

Select slave receive timing for the transmit clock.

&Y0

Recall stored profile 0 upon power up.

&Y1

Recall stored profile 1 upon power up.

&Zn=x

Store dial string x (to 35) to location n (0 to 3 depending upon modem model).

%E0

Disable line quality monitor and auto retrain.

%E1

Enable line quality monitor and auto retrain.

%E2

Enable line quality monitor and fallback/fall forward.

Return received line signal level.

Report the line signal quality.

\G0

Disable modem to modem flow control.

\G1

Enable modem to modem flow control.

\Kn

Controls break handling during three states:

When modem receives a break from the DTE:
\K0,2,4

Enter on-line command mode, no break sent to the remote modem.

\K1

Clear buffers and send break to remote modem.

\K3

Send break to remote modem immediately.

\K5

Send break to remote modem in sequence with transmitted data.

When modem receives \B in on-line command state:
\K0,1

Clear buffers and send break to remote modem.

\K2,3

Send break to remote modem immediately.

\K4,5

Send break to remote modem in sequence with transmitted data.

When modem receives break from the remote modem:
\K0,1

Clear data buffers and send break to DTE.

\K2,3

Send a break immediately to DTE.

\K4,5

Send a break with received data to the DTE.

\N0

Select normal speed buffered mode.

\N1

Select direct mode.

\N2

Select reliable link mode.

\N3

Select auto reliable mode.

\N4

Force LAPM mode.

\N5

Force MNP mode.

2.2.

ECC COMMANDS

%C0

Disable data compression.

%C1

Enable MNP 5 data compression.

%C2

Enable V.42 bis data compression.

%C3

Enable both V.42 bis and MNP 5 compression.

\A0

Set maximum block size in MNP to 64.

\A1

Set maximum block size in MNP to 128.

\A2

Set maximum block size in MNP to 192.

\A3

Set maximum block size in MNP to 256.

\Bn

Send break of n x 100 ms.

Содержание LPM-14-E











































Результаты поиска

Содержание LPM-14-E

Отзывы:

Бренды по названию

Популярные бренды

Peek Traffic LPM-14-E, Справочное руководство

Результаты поиска

Содержание LPM-14-E

Отзывы:

Бренды по названию

Популярные бренды