manualshive.com logo in svg

Peek Traffic LPM-14-E, Справочное руководство

Поделиться
Скачать
Peek Traffic LPM-14-E Скачать руководство пользователя страница 16

 

3-5 

In - Identification 

The modem reports to the DTE the requested result according to the command parameter. 

I0 

Reports product code (e.g., 

“

14400

”

). 

I1 

Reports a precomputed checksum (see firmware release notes). 

I2 

Reports 

“

OK

”

. 

I3 

Reports firmware revision (VX.XXX)-model code (A = 64K US, C = 128K US, D = 128K W-Class, E = 64K W-
Class), interface type (S = serial; P = parallel), and MCU model (29 = C29; 39 = C39) (e.g., 

“

V1.297-CS29

”

). 

I4 

Reports OEM defined identifier string (e.g., 

“

RC96ACL

”

) in either Hayes-compatible binary format.  

I5 

Reports Country Code parameter (e.g., 

“

022

”

). 

I6 

Reports modem data pump model and internal code revision (e.g., RC144DPL Rev CE). 

I7 

Reports the DAA code. (e.g., 000 for US or Canada) 

Result Codes: 

OK 

n = 0 to 7. 

ERROR 

Otherwise. 

Ln - Speaker Volume 

The modem sets the speaker volume control according to the parameter supplied. The parameter value, if valid, is written to S22 bits 0 and 1. 

L0 

Low volume. 

L1 

Low volume. (Default.) 

L2 

Medium volume. 

L3 

High volume. 

Result Codes: 

OK 

n = 0 to 3. 

ERROR 

Otherwise. 

Mn - Speaker Control 

This command selects when the speaker will be on or off. The parameter value, if valid, is written to S22 bits 2 and 3. 

M0 

Speaker is always off. 

M1 

Speaker is on during call establishment, but off when receiving carrier. (Default.) 

M2 

Speaker is always on. 

M3 

Speaker is off when receiving carrier and during dialing, but on during answering. 

Result Codes: 

OK 

n = 0 to 3. 

ERROR 

Otherwise. 

Nn - Automode Enable 

This command enables or disables Automode detection. The parameter value, if valid, is written to S31 bit 1. 

N0 

Automode detection is disabled. A subsequent handshake will be conducted according to the contents of S37 
or, if S37 is zero, according to the most recently sensed DTE speed. 

N1 

Automode detection is enabled. A subsequent handshake will be conducted according to the Automode 
algorithm supported by the modem. This command is equivalent to F0. (Default.) 

Result Codes: 

OK 

n = 0 or 1. 

ERROR 

Otherwise. 

On - Return to On-Line Data Mode 

This command determines how the modem will enter the on-line data mode. If the modem is in the on-line command mode, the enters the 
on-line data mode with or without a retrain. If the modem is in the off-line command mode (no connection), ERROR is reported. 

O0 

Enters on-line data mode without a retrain. Handling is determined by the Call Establishment task. Generally, if 
a connection exists, this command connects the DTE back to the remote modem after an escape (+++). 

O1 

Enters on-line data mode with a retrain before returning to on-line data mode. 

Result Codes: 

OK 

n = 0 or 1 and a connection exists. 

ERROR 

Otherwise or if not connected. 

Содержание LPM-14-E











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды