background image

Installation of Host Computer and Peripherals

Standalone Installation

3-3

Cabling

In preparation for cabling, Pearson NCS recommends that you do the following:

Set the computer on the back lip of the shelf during cable installation so that 

the back of the computer is tilted up. This provides easier access to the 

computer's ports.

Uncoil all cords and cables, separate them, and lay them out on the floor.

The following cabling instructions are for a standalone configuration. Refer to 

Figure 3-4, Figure 3-5, and Table 3-1 at the end of this chapter.

1.

Install the computer power cord.

Attach the power cord connector to the back of the computer.

Ensure that the other end is plugged into the scanner's power strip.

2.

Complete installation of the 25-pin straight through cable from the 

PRTCON

 

board (for the optional printer) to the back of the computer.

One end of this cable is already attached to the 

PRTCON

 board.

Connect the other end to the back of the computer.

3.

Complete installation of one 6-pin DIN cable from the 

KEMCON

 board (for the 

keyboard) to the back of the computer.

One end of this cable is already attached to the 

KEMCON

 board.

Connect the other end to the back of the computer in the keyboard port.

4.

Complete installation of the other 6-pin DIN cable from the 

KEMCON

 board 

(for the mouse) to the back of the computer.

One end of this cable is already attached to the 

KEMCON

 board.

Connect the other end to the back of the computer in the mouse port.

5.

Complete installation of the 5 BNC/15-pin DIN cable from the bulkhead (for 

the monitor) to the back of the computer.

One end (5 BNC end)  is already attached to the bulkhead.

Connect the other end (15-pin DIN) to the back of the computer.

Note:

Connect this cable to the 15-pin connector on the video card in the first 

expansion slot. Do not connect to the 15-pin connector on the system board.

6.

Complete installation of the 50-pin high density ribbon cable from the 

Camera 

Controller

 board to the Hobbes interface connector on the computer.

One end of this cable is already connected to the scanner's 

Camera 

Controller

 board at J1.

Connect the other end to the external connector for the scanner interface 

(Hobbes) card (P2) on the back of the computer.

Содержание OpScan iNSIGHT 70

















































Отзывы: