PDL D3-2.5 Скачать руководство пользователя страница 98

Страница: 98 / 113

Microdrive Series Instruction Manual

4201-109 Rev I

APPENDIX 3: LOCAL KEYBOARD OPERATION

When delivered, the Microdrive is set in the standard

configuration. This configuration allows for normal remote

control, but not for local control via the keyboard.

The following steps are necessary to disable external inputs

and be able to use the keyboard for local control. This is

particularly useful for commissioning purposes.

Screen

Title

Initialise

Setting

Function

Only do this if you wish to reset all keyboard

settings to the ex-factory state.

Screen

Title

Commission

Setting

Function

If not already set to Y.

Screen

Title

Short Menus

Setting

Function

Enables the full menus - necessary to access

the screen controls.

Screen

Title

Input Mode

Setting

Function

Disables multi-function control input terminals.

This is not a strictly necessary step - you may

still use external switch controls with keyboard

control of stop/start.

Screen

Title

Reference Frequency

Setting

Keyboard

Function

Selects Screen -2 as the reference frequency

input source.

Screen

Title

Keyboard control

Setting

Function

Enables Screen -1, allowing stop/reset and

start control of the Microdrive.

Screen

Title

Short Menus

Setting

Function

Returns to short menus (only necessary if full

menu features are not required).

Screen

-1

Title

Stop-Rst / Start

Setting

Function

Pressing Select and + will now start the

Microdrive.

Pressing Select and will now stop the

Microdrive. It will also reset any fault conditions.

Screen

-2

Title

Keyboard Frequency Control

Setting

Function

Select and +/ can be used to increase or

decrease the reference frequency.

Screen

21, 22

Title

Min Fr, Max Fr

Setting

Function

The minimum and maximum frequency settings

limit the output frequency range.

WARNING:

Selecting negative frequencies will give

reverse operation of the motor.

Содержание D3-2.5


















































































































Результаты поиска

Содержание D3-2.5

Отзывы:

Бренды по названию

Популярные бренды

PDL D3-2.5, Инструкция по эксплуатации

Результаты поиска

Содержание D3-2.5

Отзывы:

Бренды по названию

Популярные бренды