PDL D3-2.5 Скачать руководство пользователя страница 87

Страница: 87 / 113

Microdrive Series Instruction Manual

4201-109 Rev I

COMMUNICATIONS TIMEOUT SELECTION

Screen

74 COMMS T/O = OFF

Description

SERIAL COMMUNICATIONS

TIMEOUT SELECTION

Options

[OFF]/[1s]/[5s]/[25s]

FUNCTION

Provides the option of tripping the Microdrive

(indicating COMMS TIMEOUT) if the time since

the last valid serial communications data

transfer has exceeded the communications

timeout period.

SETTING UP

If a Microdrive serial communications option

module is not installed, leave this screen set to

OFF (the timeout feature is active whether a

Microdrive serial communications option module

is fitted or not).

If a Microdrive serial communications option

module is installed, select the required timeout

period.

Notes:

Select a timeout period which exceeds the the

time between valid serial communication data

transfers.

If the serial communications baud rate (Screen

51) is set to OFF, the communications timeout

feature is disabled.

CURRENT LIMIT MODE

Screen

75 I LIM MODE = I

Description

CURRENT LIMIT MODE

Options

[I] CURRENT/[TQ] TORQUE

FUNCTION

Selects current limit to control on inverter

current magnitude or on the torque component

of inverter current.

SETTING UP

The Microdrive can be configured to limit the

absolute value of inverter current (Screen 75

set to I) or to limit the torque component of the

current (Screen 75 set to TQ).

The torque component of current is the current

which is in phase with the voltage. Owing to

the high efficiency of the induction motor over

a wide range of speed and load, the in-phase

current is closely related to the torque

generated by the motor.

By setting the I LIM MODE to TQ it is possible

to operate the inverter in torque limit control.

For linear control, however, the minimum flux

(Screen 25) must be set to 100% and the

inverter needs to be in the constant torque

region of operation (i.e., output voltage less

than or equal to input voltage).

The power factor of the motor will cause the

output current to be 10% to 20% higher than

the torque component of current.

Inverter current = torque current

power factor

For normal operation, set I LIM MODE to I

(current).

Torque limit control is useful over a wide range

of current levels, but becomes inaccurate

near zero frequency.

Содержание D3-2.5


















































































































Результаты поиска

Содержание D3-2.5

Отзывы:

Бренды по названию

Популярные бренды

PDL D3-2.5, Инструкция по эксплуатации

Результаты поиска

Содержание D3-2.5

Отзывы:

Бренды по названию

Популярные бренды