PDL D3-2.5 Скачать руководство пользователя страница 38

Страница: 38 / 113

Microdrive Series Instruction Manual

4201-109 Rev I

Additional LEDs on Microdrive-i -

LED

GREEN - TRANSISTOR

OVERLOAD U+, U-, V+, V-, W+, W-

Actual Indication

IGBT being driven.

Notes:

This is not the same as transistor

conducting.

LED

RED - TRANSISTOR OVERLOAD

U+, U-, V+, V-, W+, W-

Actual Indication

Extreme current overload of

indicated IGBT.

Implication

Output short circuit or internal IGBT

failure.

LED

+24V SUPPLY

Actual Indication

+24V supply is present.

LED

+17.5V

Actual Indication

+17.5V CT supply present (check

F3, 2A, +24V supply).

LED

-12.5V

Actual Indication

-12.5V CT supply present (check F4,

500mA, -12.5V supply).

LED

SOFT CHARGE

Actual Indication

Soft charge SCR trigger supply is

present (check F5, 5A, SCR gate

supply).

1.7.5 FUSE FAILURE

The Microdrive incorporates electronic protection. The

fuses are for safety back-up.

Refer to the appropriate UD3 or UDi section for fuse details.

Microdrive-3 (UD3):

Supply fuses -

fitted by customer at point of supply.

Possible reason for failure

Wrong fuses; supply surge; age or cyclic

stress failure; fault in supply cable to UD3;

UD3 failure.

Action

Check cable, UD3. Isolate UD3 and replace

fuses. Test. If OK reconnect UD3 and

retest. If failure persists replace UD3 or

request service.

F1 +24V supply fuse

fitted on UD3 power board.

Possible reason for failure

Overload of +24V supply or low voltage

supplies derived from +24V; faulty fan; faulty

control PCB.

Action

Check UD3 for obvious faults to low voltage

DC supplies; replace with correct fuse;

check operation; if failure persists replace

UD3 or request service.

F2 2A SMPS DC bus fuse -

fitted on UD3 power board;

UD3-31

to UD3-70.

Possible reason for failure

Fault in switch mode power supply.

Action

WARNING:

This fuse MUST NOT be replaced with a

glass fuse (a glass fuse will rupture and

cause catastrophic damage). Use only the

specified 440Vac 2A ceramic fuse. Replace

fuse. If failure persists replace UD3 or

request service.

Microdrive-i (UDi):

Supply fuses -

at point of input termination to the

Microdrive.

Possible reason for failure

Supply surge; age or cyclic stress failure;

wrong fuses; fault in supply cable to

Microdrive; Microdrive failure.

Action

Check input cables and Microdrive for any

signs of a fault. Isolate Microdrive and

replace fuses. Test. If OK, reconnect

Microdrive and retest. If failure persists

replace Microdrive, or request service.

UDi DC bus fuses

Possible reason for failure

Supply surge; age or cyclic stress failure;

wrong fuses; fault in output cable to motor;

UDi failure.

Action

Isolate UDi. Check output cables; check

UDi. Unless confident fault found and

cured, contact Service Agent. Replace

fuses. Reconnect UDi and test. If failure

persists replace UDi, or request service.

Содержание D3-2.5


















































































































Результаты поиска

Содержание D3-2.5

Отзывы:

Бренды по названию

Популярные бренды

PDL D3-2.5, Инструкция по эксплуатации

Результаты поиска

Содержание D3-2.5

Отзывы:

Бренды по названию

Популярные бренды