PCM FW6 Скачать руководство пользователя страница 8

FW6 Building Instruction                                                                                                                      February 2015 
                                                                                                                        

www.pcm.at                                                                                                                                                            

6.  Fuselage 

 
 

6.1 Radio board 
 

First of all, push the ballast 
tube into the fuselage. For 
safety, you should only 
stick it when all parts are 
well positioned. 
 

 

At the moment we 
recommend the servo

 

Graupner DES 281

Therefore the radio board 
which is enclosed in the kit 
has cuttings prepared for 
this servo. 
 
In order to utilize the 
available space optimally, 
we 

tilt the radio board 

slightly

. (If you look in 

flight direction, the upper 
edge is shifted to the right, 
the lower edge to the left.) 
In addition, we 

bend

 the 

servo levers easily

. By 

this, the maximum 
deflections can be 
achieved.  
 
For the 

rudder

 and 

elevator

 we still 

recommend 

D47 from 

Dymond

 
The assembly plates of the 
D47 are situated a bit 
deeper than the ones of 
the Graupner servos. 
Therefore we supply a 

U-

formed part

 to put below 

the assembly plates and 
lift the D47 to the same 
height.  
 
These are the tried and 
tested 

lengths for the 

levers of the servos

Lever for aileron: 13mm 
Lever for elevator: 10mm 
Lever for rudder: 9mm 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 

 
 

Содержание FW6





















Отзывы: