PCM FW6 Скачать руководство пользователя страница 3

FW6 Building Instruction                                                                                                                      February 2015 
                                                                                                                        

www.pcm.at                                                                                                                                                            

 
 

 

DATA 
 

 

1.  Kit 

– contents 

 

 

Fu canopy 
Wing 
Rudder and elevator CFR 

 

Radio board 
CFR ballast tube 
Lever for controlling rudder, 1 pc. 
Lever for controlling elevator, 1 pc. 
Kevlar wire for controlling rudder and elevator 
Steel wire for torsion springs, 2 pc. 
Brass pipes for levers of ailerons, 2 pc. 
Aluminium pipes for push rods for ailerons, 2 pc. 
1mm steel wire for controlling ailerons, 4 pc. 
2mm carbon tubes for controlling ailerons, 2 pc. 
Screws for fixing wing, 2 pc.  
Nylon screws for fixing elevator, 2 pc. 
Throwing blade, 1 Stk.  
Lead balls for ballast 
1,5mm flexible steel wire for ballast 
1,5mm normal steel wire for ballast hook 
Bowden cable inner tube, 3cm 
D47 Servo support

 

Micro ball connectors 

 
 

Building instruction (for download from our website) 

 
 

 

2.  What else do you need: 

 

 

Epoxy-glue (for example UHU 300 endfest or Pattex Stabilit) 
Super glue, both runny and thick 
Carbon rovings 

 

Electrical equipment (On/Off-switch, cables, plug...) 
Electronic equipment 
Shrinking tube... 

 

3.  Electronic equipment 

 

Servo aileron: 

- Graupner DS 281 (cuttings on radio board are prepared for this 
servo) 
 

Servo rudder and elevator: 
 
 

- Dymond D-47 (cuttings on radio board are prepared for this servo) 

Same style: 

- Futaba FS31 
- Modell Expert X31 

 

Accumulators:

 

- GP NiMH Accu 35AAAH, Weight/cell 6g 
  (1,2 Volt 0,35 Ah 1/2AAA) 

 

Receiver: 

- 2,4GHz possible due to kevlar fuse cone 
- Futaba R6106HFC FASST 
- Multiplex RX-5 light M-link 
- Mulitplex RX-6 light M-link 
- Spektrum AR6115e 
- Orange RX DSM2 
Apart from RX-6 all receivers must be removed from their casings and 
covered with heat shrink tube. See Chapter receiver installation.

 

Содержание FW6





















Отзывы: