background image

2

Motherboard User’s Guide

High Bandwidth 1 GB/Sec 16-Bit Ultra V-Link Host Controller --

Supports 66MHz, 4X and 8X transfer modes, Ultra V-Link Host
interface with total bandwidth of 1 GB/sec

Advanced System Power Management Support -- ACPI 2.0 and PCI

Bus Power Management 1.2 compliant

PCI to system memory data streaming up to 132Mbyte/sec (data sent to

north bridge via high speed Ultra V-Link interface)

PCI-2.2 compliant, 32-bit 3.3V PCI interface with 5V tolerant inputs

Support three PCI slots of arbitration and decoding for all integrated

functions and LPC bus.

Dual Channel Serial ATA/RAID Controller—Complies with Serial ATA

Specification Revision 1.0

Memory Support

Two 184-pin 2.5V DIMM sockets for DDR SDRAM memory modules

Supports 

DDR400

/333/266 memory bus

Maximum installed memory is 2GB

Expansion Slots

One CNR slot

One 

8X

 AGP slot

Three 32-bit PCI slots

Onboard IDE channels

Two IDE Connectors

Supports PIO (Programmable Input/Output) and DMA (Direct Memory

Access) modes

Supports IDE Ultra DMA bus mastering with transfer rates of 

133

/100/

66 MB/sec

Serial ATA

Two Serial ATA Connectors

Transfer rate exceeding best ATA (~150 MB/s) with scalability to higher

rates

Low pin count for both host and devices

AC’97 Codec

Compliant with AC’97 2.3 specification

16-bit Stereo full-duplex CODEC with independent and variable

sampling rate

Support for 3.3v digital, 5v analog power supply and low power

consumption management

Three analog line-level stereo inputs with 5-bit volume control:

LINE_IN, CD, AUX

Front-Out, Surround-Out, MIC-In and LINE-In Jack Sensing

Two analog line-level mono input

Содержание A21G





































Отзывы: