background image

i

Motherboard User’s Guide

This publication, including photographs, illustrations and software, is under the
protection of international copyright laws, with all rights reserved. Neither this
guide, nor any of the material contained herein, may be reproduced without the
express written consent of the manufacturer.
The information in this document is subject to change without notice. The
manufacturer makes no representations or warranties with respect to the
contents hereof and specifically disclaims any implied warranties of merchant-
ability or fitness for any particular purpose. Further, the manufacturer reserves
the right to revise this publication and to make changes from time to time in the
content hereof without obligation of the manufacturer to notify any person of
such revision or changes.

Trademarks

IBM, VGA, and PS/2 are registered trademarks of International Business
Machines.
AMD, Athlon 64 Sempron are registered trademarks of Advanced Micro Devices
Inc.
Microsoft, MS-DOS and Windows 98/ME/2000/XP are registered trademarks of
Microsoft Corporation.
AMI is a registered trademark of American Megatrends Inc.
Other names used in this publication may be trademarks and are acknowledged.

Static Electricity Precautions

1. Don’t take this motherboard and components out of their original static-

proof package until you are ready to install them.

2. While installing, please wear a grounded wrist strap if possible. If you

don’t have a wrist strap, discharge static electricity by touching the bare
metal of the system chassis.

3. Carefully hold this motherboard by its edges. Do not touch those

components unless it is absolutely necessary. Put this motherboard on
the top of static-protection package with component side facing up
while installing.

Pre-Installation Inspection

1. Inspect this motherboard whether there are any damages to components

and connectors on the board.

2. If you suspect this motherboard has been damaged, do not connect

power to the system. Contact your motherboard vendor about those
damages.

Copyright © 2005

All Rights Reserved

A21G Series, V1.0

April 2005

Содержание A21G





































Отзывы: