background image

 

 

 

 

MO 9742 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Operators Manual 

 
 
 
 

Rev 1.1 

 

MO9740 Manual 

Proprietary Statement 

This manual contains proprietary information of Paxar UK Ltd. It is intended solely for the 
information and use of parties operating and maintaining the equipment described herein. Such 
proprietary information may not be used, reproduced, or disclosed to any other parties for any other 
purpose without the expressed written permission of Paxar UK Ltd. 

 
Product Improvements 

Continuous improvement of products is a policy of Paxar UK Ltd. All specifications and signs are 
subject to change without notice.   

 

FCC Compliance Statement

   

NOTE:

 

This equipment has been tested and found to comply with the limits for a Class A digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that the interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures:   

  Reorient or relocate the receiving antenna. 

  Increase the separation between the equipment and the receiver. 

  Connect the equipment into an outlet on a circuit different than that to which the receiver is 

connected. 

  Consult the dealer or an experience Radio/TV technician for help

NOTE:

 This unit was tested with shielded cables on the peripheral devices.  Shielded cables must be 

used with the unit to insure compliance. The user is cautioned that any changes or modifications not 
expressly approved by Paxar UK Ltd. could void the user’s authority to operate the equipment.   
 

Liability Disclaimer

   

Paxar UK Ltd takes steps to assure that its published engineering specifications and manuals are 
correct; however, errors do occur. Paxar UK Ltd. reserves the right to correct any such errors and 
disclaims liability resulting there from. 

 
No Liability for Consequential Damage 

In no event shall Paxar UK Ltd. or anyone else involved in the creation, production, or delivery of the 
accompanying product (including hardware and software) be liable for any damages whatsoever 
(including, without limitation, damages for loss of business profits, business interruption, loss of 
business information, or other pecuniary loss) arising out of the use of or the results of use of or 
inability to use such product, even if Paxar UK Ltd. has been advised of the possibility of such 
damages.   

Содержание MO 9742




































Отзывы: