Patton SmartNode 4900 Скачать руководство пользователя страница 35

Страница: 35 / 76

Installing the IpChannel Bank

SmartNode 4900 User Manual

3 • Hardware installation

Insert the stripped end of the positive lead into the

+DC input

of the terminal block. Tighten the screw

until the power lead is firmly fastened. Repeat the procedure for the negative lead, using the

-DC input

the terminal block. Make sure that all strands of the wire are captured and that there are no exposed wires.

Repeat steps

through

to install the remaining DC power connection.

Connect the equipment to a 36–72 VDC, 2.5A supply source that is electrically isolated from the AC
source. The 36–72 VDC source is to be reliably connected to earth ground.

Verify that the green

POWER

LED is lit.

Hardware installation is complete. Refer to chapter 4,

“Getting started with the SmartNode 4900 Series”

page 36.

An approved external power supply that incorporates a discon-
nect device must be used and positioned within easy reach of
the operator’s position.

CAUTION

Содержание SmartNode 4900













































































Результаты поиска

Содержание SmartNode 4900

Отзывы:

Похожие инструкции для SmartNode 4900

Бренды по названию

Популярные бренды

Patton SmartNode 4900, Руководство пользователя

Результаты поиска

Содержание SmartNode 4900

Отзывы:

Похожие инструкции для SmartNode 4900

Бренды по названию

Популярные бренды