Patton SmartNode 4900 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 76

background image

SmartNode 4900 Series detailed description

20

SmartNode 4900 User Manual

1 • General information

Reset button behavior

For those SmartNode devices that have a

Reset

button on the rear panel, its behavior is as follows:

•

To restart the unit with the current startup configuration—Press for less than 1 second and release the

Reset

button. The SmartNode will restart with the current startup configuration.

•

To restart the unit with factory default configuration—Press the

Reset

button for 5 seconds until the Power

LED starts blinking. The unit will restart with factory default configuration.

•

To restart the unit in bootloader mode (to be used only by trained SmartNode technicians)—Start with the
unit powered off. Press and hold the

Reset

button while applying power to the unit. Release the

Reset

button

when the

Power

LED starts blinking so the unit will enter bootloader mode.

Table 3. Port descriptions

Port

Description

ETH 0/0

(WAN Ethernet 0/0 port) 10/100Base-Tx full-/half-duplex, RJ-45, auto detection and auto-

MDI-X connects the unit to an Ethernet WAN device (for example,
a cable modem, DSL modem, or fiber modem).

ETH 0/1

(LAN Ethernet 0/1 port) 10/100Base-Tx full-/half-duplex, RJ-45, auto detection and fall-

back, connects the unit to an Ethernet LAN.

Expansion

•

V.35 serial port—DB-25 connector, data rates up to 2 Mbps,
Frame Relay or PPP protocols,

Status

and

Activity

LED indicators, configured as DTE

•

X.21 serial port—DB-15 connector, data rates up to 2 Mbps,
Frame Relay or PPP protocols,

Status

and

Activity

LED indicators, configured as DTE

Console

(RS-232 control port)

Used for service and maintenance, the Console port, an RS-232
RJ-45 connector with EIA-561 pinout, connects the router to a
serial terminal such as a PC or ASCII terminal (also called a dumb
terminal). Asynchronous default data rate 9600 bps, hardware
DSR and DTR signals for external modems are wired directly
together internally

FXS Ports

(4900/JS models)

For connection of up to 32 analog FXS devices (selectable for 12,
16, 24, or 32). Either a 50-pin or 64-pin RJ21X connector that
connects the router to an analog terminal (a telephone, for exam-
ple) FXO port. EuroPOTS support (ETSI EG201 188).

FXO Ports

(4900/JO models)

For connection of up to 32 analog FXO devices (selectable for
12, 16, 24, or 32). FXO RJ-11(6 position, 4 wire) connectors that
connect the product with an analog line (FXS port). EuroPOTS sup-
port (ETSI EG201 188).

Table 4. Rear panel expansion port LED descriptions

LED

Indication

Description

Status

Solid yellow

Proper signals are present for modem communication

Activity

Flashing yellow

Transmit or receive traffic is present on the serial interface

«
...
18
19
20
21
22
...
»

Содержание SmartNode 4900













































































Отзывы:

Нет отзывов

Похожие инструкции для SmartNode 4900

Бренд: D-Link Страницы: 38

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 20

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 12

DIR-615 - Wireless N Router

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 124

Web Smart DES-1210-28P

Бренд: D-Link Страницы: 6

2Voice + 4SW VoIP Router DVG-1402S

Бренд: D-Link Страницы: 57

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 23

Express EtherNetwork DI-604

Бренд: D-Link Страницы: 7

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 97

SharePort DIR-825

Бренд: D-Link Страницы: 2

Amplifi DIR-645

Бренд: D-Link Страницы: 28

Бренд: F5 Страницы: 72

Adapter Bracket

Бренд: Paradyne Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды