background image

Powering up the EnviroNET

32

EnviroNET User Manual 

4 • Operating the EnviroNET

Powering up the EnviroNET

The EnviroNET is designed to be powered on automatically.  There is no power switch.  The green power 
LED will light when the power is on (ET and EC models only).

To power the EnviroNET:

1.

You need to wire the power cable. If you haven’t done this already, go to the section, 

“Wiring the power”

 

on page 17 in Chapter 2,

 “Installing the EnviroNET” 

.

2.

After all of the cables are properly wired, close and lock the case. Plug the power cable into an electrical 
outlet.

Note

Once in operation, the EnviroNET will run over all temperatures 
without user intervention.

LEDs (ET and EC models only)

The EnviroNET has two LEDs, 

Power 

and 

Temperature Control Indicator

.

ET models 

Power: 

The Power light will be on when the EnviroNET is operating normally. 

Temperature Control: 

The Temperature Control Indicator light will be on when the heater is on. The 

heater will automatically come on at temperatures under -40ºC (-40ºF). When the Temperature Control 
Indicator light is on, the EnviroNET will not be powered on to operate and the Power light will be off. 

EC models

Power: 

The Power light will be on when the EnviroNET is operating normally. 

Temperature Control

: The Temperature Control Indicator light will be on for temperature control condi-

tions, such as when the fan is operating.

Note

EH models 

do not have a fan or heater, therefore they do not have 

LEDs. 

Содержание EnviroNET 2100 Series












































Отзывы: