background image

March 2016

WARNINGS

•  Do not store or use gasoline or other 

fl

 ammable vapors or liquids in the vicinity of this or any other equipment.

•  Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.
•  Read the installation and maintenance instructions thoroughly before installing or servicing this equipment.
•  Have the equipment installed by a quali

fi

 ed installer in accordance with all federal, state and local codes.

•  Do not install or use without all 4 legs. 
•  This equipment is for use in non-combustible locations only.
•  Do not obstruct the 

fl

 ow of combustion and ventilation air.

•  Do not spray controls or the outside of the equipment with liquids or cleaning agents
•  Allow for hot parts to cool before cleaning or moving.
•  This equipment should only be used in a 

fl

 at, level position.

•  Do not operate unattended.
•  Any loose dirt or metal particles that are allowed to enter the gas lines on this equipment will damage the valve and 

affect its operation.

•  If you smell gas, follow the instructions provided by the gas supplier.  Do not touch any electrical switch; do not try to 

light the burner; do not use a telephone within close proximity. 

SET-UP

1.  Remove all packing material and tape, as well as any protective plastic from the equipment.
2.  Place the equipment in the desired position and height.
3.  Install the four (4) legs onto the equipment.
4.  Clean and dry the equipment thoroughly before using.

BEFORE INSTALLATION

•  Installation of this device should be done by professional technicians
•  This device is suitable for area whose altitude is lower than 6,500 ft. If it is higher than this altitude, please contact 

the manufacturer.

•  Installation of this unit should conform to provisions of gas safety, installation and usage
•  This device should be kept a minimum clearance of 4” away from non-combustible objects on both sides and 6” at 

the back (e.g. walls, windows etc.). Do not install on a 

fl

 ammable 

fl

 oor or around other combustible objects.

TO INSTALL - 

Please read manual thoroughly before installation and operation

1.  Select a location for the unit that has a level, solid, non-skid surface that is non-

fl

 ammable.

2.  Screw legs into the permanently fastened nuts on the four corners of the unit and tighten by hand.  Legs must be 

installed for proper ventilation to the unit.

3.  Level unit by adjusting the four feet and tighten securely.  The adjustable feet have an adjustable range of one inch.  

Do not slide unit with the legs mounted.  Lift if necessary to move unit.  

4.  The supplied gas pressure regulator is factory set at 4” Natural Gas W.C or 10” Propane Gas.
5.  Do not obstruct the 

fl

 ow of combustion and ventilation air under the unit by the legs or behind the unit by the 

fl

 ue.  

Do not place objects between the bottom of the unit and countertop.

6.  There must be adequate clearance for removal of the front panel.  All major parts except the burners are removable 

through the front if the gas is disconnected.  

7.  It may be unnecessary to adjust the balance of gas volume and air supply to each burner.  This must be done by an 

authorized service technician.

  

      

CODES AND STANDARDS

This item must be installed in accordance with:
In the United States:
  

State and local codes, or in the absence of local codes, with:

National Fuel Gas Code, ANSI-Z223.1/NFPA #54 (latest edition).  Copies may be obtained from The American Gas 
Association Accredited Standards Committee Z223, @ 400 N. Capital St. NW, Washington, DC 20001 or the Secretary 

Содержание PLATINUM











Отзывы: