background image

– 24 –

Model

LR6-ILWMNW

LR6-ILWCNW

Rated Voltage

24 V DC

Voltage tolerance range

18 V DC to 30 V DC

Rated current consumption

Standard

170 mA

Maximum

200 mA

Rated power consumption

Standard

4 W

Maximum

5 W

Inrush current

10 A / 0.3 msec

Ambient operating temperature

-20 °C to +50 °C

Ambient operating humidity

90 % RH or less; No condensation

Ambient storage temperature

-30 °C to +60 °C

Ambient storage humidity

90 % RH or less; No condensation

Installation location

Indoor

Installation direction

Upright direction

Protection Rating

IP65, NEMA TYPE 4X, 13

Environmental 

conditions

When installed in the upright direction

Insulation resistance

5 M

Ω

 or more at 500 V DC between charging parts and non-charging metal parts

Withstanding voltage

1 minute at 500 V AC between charging parts and non-charging metal parts

Mass (Tolerance: ±10 %)

0.2 kg

0.16 kg

Exterior dimensions

See “

3

 Names and Dimensions”

Compliance standards

UL 508, CSA-C22.2 No. 14, EMC Directive (EN 61000-6-4, EN 61000-6-2)

RoHS Directive (EN 50581), FCC Part 15 Subpart B Class A

KC (KN 61000-6-4, KN 61000-6-2)

Function

- LED control

- Buzzer control

- Operational mode/pattern settings

- LED 

fl

 ashing/intermittent

- Buzzer Pattern Settings

Communication 

Speci

fi

 cation

IO-Link revision

1.1

Transmission speed

COM2 (38.4 kbps)

Minimum cycle time

8 ms

Processing data 

length

6 byte / 0 byte (input from master / output to master)

Vendor ID

763

Device ID

80001

The requirements in each law and regulation are only included in the language designated by each law and regulation. 

Check the instruction manuals published in each language.

Содержание LR6-IL






























Отзывы: