Paso P8136, Инструкция по эксплуатации

Страница: 40 / 60

DATASHEET
α
10
6. USE
6.1 Selecting the music input
It is possible to use the PROGRAM SELECTION keypad ( 4 to 9 ) to select the desired music source ( TAPE , CD , TUNER , AUX ).
Adjust the volume of the selected source by holding down the appropriate key and turning the knob ( 2 ). To include or exclude background music
for a given zone it is sufficient to press the relevant PROGRAM INSERTION button ( 10 ) on the front panel of the equipment: the signalling lamps
corresponding to the buttons will light up to indicate the zones that have been selected with inclusion of music.
6.2 PMB106/PMB112 microphone stations
It is possible to associate a specific group of call zones, output events and digital messages with each of the keys of the PMB106/PMB112 Master
microphone stations (including the PTT/LOCK and ALL * keys). Furthermore, the associated zones can be selected by means of each P8136
interconnected within the system (multi-master system). In the default configuration the selection keys are associated with their respective zone
numbers of the main master system.To change the call zone configuration, the keys must be programmed using the P8136 Manage r software.
ATTENTION : If more than one key with various types of configuration (speech, messages and output events) are selected, the ‘speech’
selections will prevail: the outputs associated with messages will not be activated while any keys associated with output events will be activated.
*
on PMB112-E expansion cards.
• Handsfree broadcasting
Select the zones in which you wish to activate handsfree broadcasting and press the PTT or LOCK keys: the LED on the base will light up to indicate
that the microphone has been activated. The LEDs of the keys corresponding to the groups in which broadcasting can be carried out will remain
illuminated. Once the call has been completed, release the PTT key or press the LOCK key again. If the ALL key on the main station is pressed, all
36 zones connected to the master P8136 will be called: the LED of the PTT will flash rapidly to indicate this type of call. Once the All Call has been
Any output events associated with the selected zones will be carried out for the whole duration of the call.
• Playing out of messages
To send pre-recorded messages - associated by means of the P8136 Manager software with the station keys – follow the procedure described above
for handsfree calls.
The message will be played out repeatedly until it is unselected.
If even only one of the zones selected is busy (whether with speech broadcasting or pre-recorded messages), the call will be cancelled and any
associated output configurations will not be performed.
If several keys associated with different messages are selected by mistake, the message corresponding to the key with the lowest number will be
played out and broadcast in all the zones associated with the keys that were selected.
• Activation of output events
Each key of the stations can be associated with an output event configuration, even if no voice broadcasting (handsfree or messages) is envisaged.
To activate these output events, select the relevant keys and press PTT/LOCK.
These keys can always be selected associated with speech keys or messages.
This must be considered a call to all effects and purposes, and the system will therefore be ‘busy’ with the base priority.
• Configuration of special keys
The first six keys of the stations can be configured to call up output events only – including SYSTEM RESET or MASTER RESET events, separately from
the handsfree call or from despatch of the message associated with them. This means that the system will NOT be busy: activation of output events
created in this way does not seize the voice line and the base can continue to function with all its other keys.
Pressing the key for more than two seconds will cause activation of the event. The LED of the corresponding key will flash to signal this activation. To
de-activate the output configuration press the key associated with the flashing LED again. If no “Out Events” configurations are associated with the
key, after the two seconds the LED will remain steady ON and will be considered an activation of zones, enabling of which will follow only after the
PTT(/LOCK) key is pressed. If the base is being used for broadcasting, “Out Event” cannot be activated until the base is freed.
It is possible to activate several “Out Event” configurations simultaneously by selecting one or more of the first 6 keys of a console and holding one of
them down for over two seconds. The LEDs of all the keys with OutEvent configurations selected will flash to indicate activation of the outputs.
All the output events activated by the bases can be status-related only and not transition events.