background image

www.parweld.com

www.parweld.com

11

9.0 eC declaration of conformity

Hereby we declare that the machines as stated below

Type: XTP-63

Conform to the EC Directives:

Low Voltage Directive 2006/95/EC

EMC Directive 2004/108/EC

Harmonised European standard: EN/IEC 60974-1

This is to certify that the tested sample is in conformity with all provisions of the above detailed EU directives and product standards.

9.1 rohs Compliance Declaration

Directive 2011/65/EU of the European Parliament

Restriction of use of certain hazardous substances in electrical and electronic equipment

Type:  XTP-63

The above listed products are certified to be compliant with the rohs directive with all homogeneous component parts being controlled to 

ensure material contents as per the list below.

Cadmium 0.01% by weight

Lead 0.1% by weight

Mercury 0.1% by weight

Hexavalent chromium 0.1% by weight

Polybrominated biphenyl’s (pbbs) 0.1% by weight

Polybrominated diphenyl ethers (pbdes) 0.1% by weight

It should be noted that under specific exempted applications, where lead is used as an alloying element the following limits are applied in 

accordance with the regulations.

Copper and copper alloy parts use less than 4% by weight of each homogeneous component. 

Steel and steel alloy parts use less than 4% by weight of each homogeneous component. 

Aluminium and aluminium alloy parts use less than 4% by weight of each homogeneous component. 

Only dispose off in authorised sites for electrical and electronic waste do not dispose of with general refuse or landfill waste.

eC D

eC

l’

Содержание XTP-63















Отзывы: