background image

www.parweld.com

6

5.0 Installation

Read entire installation section before starting installation.

SaFetY preCautIOnS

• ELECTRIC SHOCK can kill.
• Only qualified personnel should perform this installation.
• Only personnel that have read and understood the Operating 

Manual should install and operate this equipment.
• Machine must be grounded per any national, local or other 

applicable electrical regulations.
• The power switch is to be in the OFF position when installing 

work cable and electrode cable and when connecting other 

equipment.

4.0 Description of Controls

1) Amperage Display. Displays the welding amperage or wire speed 

during welding   
2) Voltage Display. Displays the welding voltage during welding
3) Voltage control This function controls the MIG welding voltage. It 

can be adjusted infinitely withing the working voltage range.

4) Negative output connection used to connect the work return cable. 

This is the 50mm Dinse connection socket.

5) MIG torch euro connector, for connection of the MIG torch
6) Latching trigger selector. 2 Arrows denotes momentary trigger, 4 

arrows denotes latching trigger.
7) Inductance control, this hardens or softens the arc in MIG welding, 
8) Amperage control for adjusting the Amperage (wire feed speed) 
Power light This indicates mains power is applied to the machine 

and that the machine is currently switched on when the light is 

illuminated. 

14) MIG wire spool holder accepts 5KG (200mm ) spools
15) Wire feed box 
16) Wire tension adjuster

ON OFF Switch for switching on or off the mains supply to the 

machine. (mounted on the rear of the machine)
 

note the output of the machine is permanently on in MMa 

mode unless the on/off switch is in the off position.

1

2

3

4

5

CO

ntr

O

lS

6

7

8

14

15

16

Содержание XTI-160 M















Отзывы: